Walk-In Tub Installation Georgetown TX Built for Safety and Comfort
Low-threshold tubs installed clean, level, and code-compliant
Walk-In Tub Installation Georgetown TX homeowners can trust starts with a proper drain, a level base, and waterproofing that holds. We install low-threshold and wheelchair-accessible tubs for seniors, veterans, and anyone who wants to bathe without stepping over a 17-inch wall. Whether you are in Sun City or Old Town, we handle the plumbing, tile, and finish in one visit.
Walk-In Tub Installation Georgetown TX Done Right
Walk-In Tub Installation Georgetown TX is the trade of removing a standard 30-by-60 bathtub and setting a sealed, low-threshold tub in its place, tied into the existing drain and hot-water line. The job involves cutting the old tub out, inspecting the subfloor for water damage, rerouting PEX piping if the filler location moves, and setting the new tub on a level bed of mortar so it does not flex. We finish the surround with cement backer board, a waterproofing membrane, and ceramic or porcelain tile, then seal every joint with silicone caulk rated for wet areas.
Most of our walk-in tub work in Georgetown comes from two groups: retirees in Sun City Georgetown who want a safer soak after a knee replacement, and families in Wolf Ranch or Berry Creek updating a hall bath before a parent moves in. A walk-in tub install in Georgetown Texas also solves a common problem in 1990s and 2000s builds, where the original tub sits on a plywood deck that has softened from a slow shower leak. We open the wall, replace the damaged section, and rebuild the surround so the new tub has a solid foundation.
Why Georgetown Homeowners Choose Walk-In Tubs
A walk-in tub is not just a bathroom upgrade. It is a daily safety improvement, a resale feature, and a way to stay in the home you already love. Here is what our Georgetown customers notice most after installation.
Step In Without Fear
A walk-in tub threshold sits 3 to 6 inches off the floor instead of the standard 17. That difference removes the leading cause of bathroom falls for adults over 65. We install textured floors and grab bars rated to 250 pounds so you can enter, sit, and stand with a hand on solid support.
Hydrotherapy That Helps
Many of the tubs we install include air or water jets, an in-line heater, and a 20-minute timer. For arthritis, neuropathy, or post-surgery recovery, warm hydrotherapy at 98 to 104 degrees loosens stiff joints. We size the tub so the pump and heater fit behind the wall without crowding the plumbing.
Fits the Existing Footprint
Most walk-in tubs drop into the same 30-by-52 or 30-by-60 alcove your old tub occupied. That means no floor plan changes, no moving the toilet, and no new door swing. We measure the rough opening, check the drain location, and order a tub that lines up with your existing PVC drain pipe.
Adds Real Resale Value
Accessible bathrooms are a selling point in Williamson County, where a large share of buyers are 55 and older. A cleanly installed walk-in tub with tile surround and a Panasonic exhaust fan reads as a thoughtful upgrade, not a medical fixture. It photographs well and answers a question buyers ask before they tour.
Our Walk-In Tub Installation Process
Every job follows the same five steps, whether you are in Rivery or Northwest Georgetown. You get a written schedule, a protected work area, and a working tub at the end of the day.
Measure and Plan
We visit your home, measure the alcove, and check the drain and supply line locations. You pick the tub model, jet package, and door swing. We confirm the tub fits the rough opening within a quarter inch and that the water heater can handle the fill volume, usually 40 to 60 gallons.
Demo and Inspection
On install day we lay drop cloths, shut off the water, and cut the old tub out in sections. We pull the surround tile, remove the cement backer board, and inspect the subfloor with a moisture meter. If we find soft wood or mold, we replace that section before anything new goes in.
Plumbing and Rough-In
We set the new tub on a mortar bed, level it, and connect the drain with PVC and the supply with PEX. A licensed plumber on our crew handles the final connections and pressure-tests the lines. This step takes two to four hours on a typical Georgetown install.
Waterproof and Tile
We hang new cement backer board, roll on a waterproofing membrane, and tape the seams. Then we set ceramic or porcelain tile with a wet saw, keep the joints even with tile spacers, and grout with a float. The surround cures overnight before we caulk the tub-to-tile joint with silicone.
Test and Walkthrough
We fill the tub, run the jets, and check every connection for drips. You get a walkthrough of the door seal, the grab bars, and the drain. We clean up, haul off the old tub, and leave you with a tub you can use the same evening.
Why Our Walk-In Tub Installation Georgetown TX Stands Out
We are a local crew, not a franchise. The same people who measure your bathroom are the ones who install the tub and come back if anything needs attention.
Licensed and Insured
We carry a TDLR contractor license, a Texas State Board of Plumbing Examiners license, and EPA Lead-Safe Certification for homes built before 1978. Every job is covered by general liability and workers comp. You get a certificate of insurance before we start, no runaround.
One-Day Installs, Most Jobs
A standard walk-in tub replacement takes one day, roughly 8 to 10 hours. Larger tubs with extensions or a full tile surround can run into a second day. We schedule the plumber and tile setter back to back so you are not waiting a week between phases.
Local to Williamson County
Our walk-in bathtub installation near me Georgetown customers call for is based right here. We know the slab elevations in Berry Creek, the older cast iron drains in Old Town Georgetown, and the HOA tile rules in Wolf Ranch. That local knowledge saves you time and rework.
Upfront Pricing, No Surprises
You get a written price before we start, including the tub, labor, tile, and haul-away. If we open a wall and find rot or a cracked drain line, we show you the problem and price the fix before we touch it. No change orders after the fact.
What Our Walk-In Tub Installation Includes
Every walk-in tub project we quote includes the labor, materials, and cleanup needed to leave you with a working, code-compliant tub. We list what is covered so you can compare quotes fairly. Add-ons like a full bathroom remodel or a new vanity are priced separately, and we tell you that up front.
What's Included
Old Tub Removal
We cut out and haul away the existing tub, whether it is cast iron, steel, or acrylic. Cast iron tubs weigh 300 to 400 pounds and have to be cut into sections to get out the door. We protect the floor and doorways on the way out.
Plumbing Connections
A licensed plumber connects the drain with PVC and the supply with PEX, sets the tub on a mortar bed, and pressure-tests the lines. If the drain location has to move, we cut and reroute it and patch the subfloor before the tub goes in.
Waterproofed Surround
We hang cement backer board, tape the seams, and roll on a waterproofing membrane. This is the layer that keeps water out of your wall. We follow TCNA standards for the tub-to-wall joint and seal it with silicone caulk rated for wet areas.
Tile and Grout
You pick ceramic or porcelain tile from brands like Daltile or MSI. We cut with a wet saw, set with tile spacers for even joints, and grout with a float. The surround is ready for use the next day after the caulk cures.
Grab Bars and Safety Hardware
We install grab bars rated to 250 pounds, anchored into studs or blocking, not just drywall. We also check the door seal, the drain, and the tub floor texture. If you want a handheld shower head or a transfer bench, we can add those.
Permit and Inspection
We pull the plumbing permit from the City of Georgetown, schedule the inspection, and meet the inspector on site. You get the sign-off paperwork for your records. This protects you if you ever sell the home or file an insurance claim.
Problems a Walk-In Tub Install Solves
Most of our Georgetown customers call because something in the bathroom is not working the way it used to. Here are the problems we hear most often, and how a walk-in tub install fixes them.
Stepping over a 17-inch tub wall feels unsafe
Falls in the bathroom are the leading cause of injury for adults over 65, and a standard tub wall is the main obstacle. One slip can mean a hip fracture, surgery, and months of recovery.
We install a walk-in tub with a 3 to 6 inch threshold, a wide door, and a textured floor. Grab bars rated to 250 pounds go in at the height you need. You step in, sit down, and close the door without lifting a leg over a wall.
The old tub leaks and the subfloor is soft
A slow shower leak can rot the plywood deck under a tub for years before you notice. By the time the floor feels spongy, the damage often runs into the joists and the wall behind the tile.
We open the wall, check the subfloor with a moisture meter, and replace any soft wood before the new tub goes in. We also replace the drain and supply lines while the wall is open, so you are not paying twice for the same access.
Arthritis or nerve pain makes soaking painful
A standard tub does not hold heat long enough and has no jets. For arthritis, neuropathy, or post-surgery recovery, a lukewarm soak does not loosen stiff joints or ease pain.
We install walk-in tubs with air or water jets, an in-line heater, and a 20-minute timer. Water stays at 98 to 104 degrees for the full soak. Many of our Sun City Georgetown clients use it daily for pain management.
The bathroom has mold and mildew on the ceiling
A walk-in tub adds moisture to the room, and if the exhaust fan is undersized or the duct is clogged, steam sits on the ceiling and feeds mold. That is a health issue and a paint problem.
We size a Broan or Panasonic exhaust fan to the room, run the exhaust fan duct to the exterior, and seal it. We also check for a clogged drain or a leaking faucet while we are in the room, so the moisture problem is solved at the source.
When Georgetown Homeowners Install Walk-In Tubs
A retiree in Sun City Georgetown wants to age in place and stop using the guest shower
We install a walk-in tub with a low threshold, grab bars, and a handheld shower head. We match the tile to the existing floor and add a Panasonic exhaust fan to control moisture. The whole project takes two days.
The homeowner bathes safely in their own bathroom again, with no need to move to a care facility or rely on a family member for help.
A family in Wolf Ranch is remodeling a hall bath before a parent moves in
We replace the old tub with a walk-in model, rebuild the surround with waterproofed backer board and porcelain tile, and install a comfort-height toilet while the floor is open. We coordinate the plumbing and tile in one visit.
The parent has a safe, private bathroom from day one, and the family avoids a second remodel later.
An Old Town Georgetown homeowner has a 1970s cast iron tub with a slow drain
We cut the cast iron tub into sections, replace the PVC drain pipe, and set a new walk-in tub on a level mortar bed. We also replace the supply lines with PEX and check the shut-off valves.
The drain runs clear, the tub is level, and the bathroom is updated without a full gut remodel.
A homeowner in Berry Creek is recovering from hip surgery and needs a tub fast
We prioritize the job, order a stock walk-in tub, and schedule the install within a week. The crew handles demo, plumbing, and tile in one day, with the caulk curing overnight.
The homeowner is soaking safely within 10 days of the first call, with grab bars placed at the right height for recovery.
Tools and Methods We Use
Tools & Equipment
Wet Saw
Cuts porcelain and ceramic tile cleanly without chipping the edge. We use it for every cut around the tub apron, the valve, and the grab bar anchors.
Moisture Meter
Checks the subfloor and wall cavity for hidden water before we set the new tub. If the reading is high, we open the area and replace the wood.
Oscillating Multi-Tool
Cuts the old tub apron, trims backer board, and cleans up the tub-to-floor joint. It gets into tight corners a saw cannot reach.
Pipe Wrench and PEX Crimper
Connects the drain and supply lines. We use PEX for supply and PVC for drain, and pressure-test both before closing the wall.
Level and Stud Finder
Sets the tub on a true level bed and locates studs for grab bar blocking. A tub that is off level by a quarter inch will pool water at the door seal.
Caulking Gun
Applies silicone caulk at the tub-to-tile joint and around the drain flange. We use a wet-area-rated caulk that stays flexible for years.
Methods
TCNA Waterproofing Standards
We follow Tile Council of North America guidelines for backer board, membrane, and tub-to-wall joints. That means taped seams, a roll-on membrane, and a flexible sealant at every change of plane. This is the standard that keeps water out of the wall.
Mortar Bed Tub Setting
We set the tub on a bed of mortar instead of foam or shims. The mortar fills the gap under the tub floor and stops flex, which is what causes cracks at the drain and door seal over time.
Pressure Testing
After we connect the supply and drain, we pressure-test the lines and fill the tub to check for leaks. We do this before the tile goes on, so any problem is fixed while the wall is still open.
Permit and Inspection
We pull the plumbing permit from the City of Georgetown and meet the inspector on site. The inspection confirms the drain, vent, and supply meet IRC and local code. You get the sign-off for your records.
How Walk-In Tub Installation Runs in Georgetown
Georgetown sits on expansive clay soil, and that matters for a tub install. The slab moves slightly with wet and dry cycles, which can throw a tub out of level if it is not set on a proper mortar bed. We check level in both directions and shim the base before the mortar sets. Most homes here are slab-on-grade, so there is no crawl space to work from, and every drain change happens through the wall or the floor. In Sun City Georgetown, we work with HOA rules on exterior venting and tile color, and we schedule around the community's quiet hours. In Old Town, we run into cast iron drains and galvanized supply lines that need replacing while the wall is open. If you are searching for walk-in bathtub installation in Georgetown TX cost, the biggest local variable is whether the drain and subfloor need repair. We check both during the measure so the quote is accurate. We also handle the plumbing permit, which the City of Georgetown requires when you alter the drain or supply.
Service Areas
Most of our accessible tub work is here. We know the HOA rules on exterior venting and the standard 30-by-60 alcove layout used in most homes.
Older homes often have cast iron drains and galvanized supply lines. We replace both while the wall is open so the new tub is not tied to failing pipe.
Newer construction with PVC drains and PEX supply. The main issue here is matching the builder-grade tile when we rebuild the surround.
Slab-on-grade homes with tight alcoves. We measure the rough opening carefully so the tub fits without cutting into the adjacent vanity or toilet space.
Local Considerations
Expansive clay soil and slab movement
A tub set on shims or foam can flex and crack at the drain. We set every tub on a mortar bed and check level in both directions before the mortar cures.
Hot, humid summers with high indoor moisture
Bathrooms here need real exhaust capacity. We size the fan to the room and run the exhaust fan duct to the exterior, not into the attic.
Older homes with cast iron and galvanized pipe
In Old Town and Downtown Georgetown, we often replace the drain and supply lines during the install. It adds a few hours but prevents a leak behind the new tile.
City of Georgetown plumbing permit requirement
Any drain or supply change needs a permit and an inspection. We pull it, meet the inspector, and hand you the sign-off so your insurance stays valid.
Sun City Tub Swap in Two Days
A 1998 home in Sun City Georgetown had a standard 30-by-60 tub with a 17-inch wall. The homeowner had stopped using it after a knee replacement and was showering in the guest bath. The surround tile was original and the caulk joint was black with mildew.
We removed the old tub, set a walk-in model with a 4-inch threshold, and rebuilt the surround with waterproofed backer board and new porcelain tile. Grab bars went in at 34 inches. The project took two days and the tub was usable on day three.
Maintenance & Follow-up
Wipe the door seal dry after each use, run the exhaust fan for 15 minutes, and re-caulk the tub-to-tile joint every three to five years. That keeps the seal flexible and the wall dry.
A family in Wolf Ranch needed a safe bathroom for a parent moving in. The hall bath had a builder-grade tub, a low toilet, and a Broan fan that vented into the attic. The floor tile stopped at the tub apron and the subfloor was exposed.
We installed a walk-in tub with air jets and an in-line heater, replaced the fan and ran the exhaust fan duct to the exterior, and set a comfort-height toilet. New porcelain tile covered the floor and surround. Total time was three days.
Maintenance & Follow-up
Flush the jets with a manufacturer-approved cleaner every month, keep the drain screen clear, and check the exhaust fan for dust twice a year. The tile and grout only need a pH-neutral cleaner.
A 1972 home near the Georgetown Square had a cast iron tub with a slow drain and a leaking faucet. The subfloor under the tub was soft from years of slow seepage, and the galvanized supply lines were corroded at the shut-off valves.
We cut the cast iron tub out in sections, replaced 6 feet of subfloor, ran new PVC drain pipe and PEX supply lines, and set a walk-in tub on a mortar bed. New waterproofing and ceramic tile finished the surround. The job took three days.
Maintenance & Follow-up
Watch for low water pressure at the tub filler, which signals a valve issue, and keep the drain clear of hair. Re-caulk the tub joint every few years and check the subfloor for soft spots if you ever see water on the floor.
How much does a walk-in tub installation cost in Georgetown TX?
Most walk-in tub installations in Georgetown run $4,500 to $12,000 in 2026, including the tub, labor, tile, and haul-away. A basic soaker with a tile surround lands near the low end. Tubs with air or water jets, an in-line heater, and a full waterproofing rebuild push toward the top. If we find subfloor rot or a cracked drain, that adds $400 to $1,500 depending on the repair.
How long does walk-in tub installation take in Georgetown Texas?
A standard walk-in tub install takes one day, usually 8 to 10 hours. That covers demo, plumbing, setting the tub, and hanging backer board. If you are adding a full tile surround with a waterproofing membrane, plan on a second day so the grout and silicone caulk can cure. We schedule both days up front so you know exactly when the tub is usable.
Do walk-in tubs qualify for Medicare in Georgetown TX?
Original Medicare does not cover walk-in tubs because they are considered a home modification, not durable medical equipment. Medicare Advantage plans sometimes include a bathroom safety benefit, and VA benefits can cover part of the cost for eligible veterans. We can provide an itemized invoice with the model number and installation breakdown so you can submit it to your plan.
Do I need a permit for a walk-in tub installation in Georgetown TX?
Yes, the City of Georgetown requires a plumbing permit when you replace a tub and alter the drain or supply lines, and most jobs do. The permit fee runs $75 to $150 and covers one inspection. We pull the permit, meet the inspector, and handle the sign-off. Skipping it can void your homeowner insurance if a leak causes water damage later.
Licensed, Insured, and Local
Certifications
Reviews
They installed a walk-in tub for my mother in Sun City. Pulled the permit, handled the inspection, and tiled the surround to match. The door seal has not leaked and the grab bars are exactly where she needs them. Fair price and no surprises.
We had a soft subfloor under the old tub and they showed us the wood before replacing it. New PVC drain, new PEX supply, walk-in tub set level on mortar. Two days total. I would use them again for any bathroom work.
Professional crew, on time, clean work. They replaced a cast iron tub in our Old Town home and rebuilt the surround with new tile and waterproofing. The exhaust fan they added cleared the steam problem we had for years.
Got three quotes for a walk-in tub in Wolf Ranch. Georgetown Bath Remodel Pros was the only one that explained the waterproofing and the permit. Install took one day and the bathroom looks great. Worth every dollar.
Related Services
Full Bathroom Remodeling
If your walk-in tub is part of a larger update, we can remodel the whole bathroom at once. That means new flooring, a vanity cabinet, lighting, and paint in a single project instead of two. Most Georgetown full remodels take two to three weeks.
Full Bathroom RemodelingBathroom Renovation
A walk-in tub often triggers a renovation because the surround tile no longer matches the rest of the room. We handle the tile, drywall, greenboard, and paint so the finished bathroom looks intentional, not patched together.
Bathroom RenovationShower Remodeling
Some homeowners choose a curbless shower instead of a walk-in tub. We build both, so we can walk you through the trade-offs in person. A shower remodel with a linear drain and Schluter waterproofing is a strong alternative for smaller bathrooms.
Shower RemodelingBathtub Remodeling
If a walk-in tub is not the right fit, we also install standard alcove tubs, freestanding tubs, and drop-in models with a quartz or granite deck. We can replace the tub and refresh the surround without touching the rest of the bathroom.
Bathtub RemodelingTile Installation
Every walk-in tub surround we build gets new tile. We set ceramic or porcelain tile from Daltile or MSI over a waterproofed backer board, cut with a wet saw, and grout with a float. Proper tile work is what keeps water out of the wall.
Tile InstallationVanity Installation
A new tub often makes the old vanity look tired. We install vanity cabinets with quartz or granite countertops, set the sink, and tie in the faucet. Matching the tub surround to the vanity finish is a small detail that lifts the whole room.
Vanity InstallationBathroom Flooring Installation
When we pull a tub, the floor underneath is usually unfinished. We install porcelain tile, luxury vinyl, or ceramic tile to match the rest of the bathroom, with a proper underlayment and a sealed transition at the tub apron.
Bathroom Flooring InstallationBathroom Countertop Installation
Quartz and granite countertops hold up well in a wet bathroom. We template, cut, and set the top, then seal the backsplash and caulk the edges. A new countertop is a fast way to modernize a bathroom around a new walk-in tub.
Bathroom Countertop InstallationToilet Installation
If the toilet sits next to the tub, we can replace it while the floor is open. We install comfort-height models from Kohler, Toto, or American Standard, set a new wax ring, and check for a running toilet or a leaking faucet before we close up.
Toilet InstallationSink Installation
Undermount and drop-in sinks both work with a new vanity. We cut the opening, set the sink with silicone caulk, and connect the drain and supply lines. If your old sink had low water pressure, we check the aerator and shut-off valves while we are in there.
Sink InstallationFaucet Installation
A walk-in tub filler and a new sink faucet are small upgrades with a big visual payoff. We install Moen, Delta, and Kohler fixtures, pressure-test the connections, and make sure the tub filler reaches the tub without splashing over the deck.
Faucet InstallationShower Door Installation
If you convert the tub area to a shower instead, we install framed and frameless shower glass. We measure the opening, set the track level, and seal with silicone caulk. A frameless door with 3/8-inch glass is the most popular choice in Georgetown.
Shower Door InstallationBathtub-to-Shower Conversion
Some homeowners decide a low-curb shower is a better fit than a walk-in tub. We remove the tub, build a sloped pan with a waterproofing membrane, tile the walls, and install a shower door. The result is easier to enter than a standard tub and easier to clean.
Bathtub-to-Shower ConversionAccessible Bathroom Remodeling
A walk-in tub is one piece of an accessible bathroom. We also widen doorways, install grab bars, lower the vanity, add a comfort-height toilet, and improve lighting. For Sun City Georgetown clients, this is often a single coordinated project.
Accessible Bathroom RemodelingBathroom Cabinets and Storage
Walk-in tubs take up more wall space than a standard tub in some layouts. We build in linen storage, a recessed medicine cabinet, or a taller vanity cabinet so you do not lose storage when the tub changes.
Bathroom Cabinets and StorageBathroom Ventilation and Exhaust Fan Installation
A walk-in tub puts more moisture in the air than a shower. We install a Broan or Panasonic exhaust fan sized to the room, run the exhaust fan duct to the exterior, and seal it so steam leaves instead of feeding mold and mildew in the walls.
Bathroom Ventilation and Exhaust Fan InstallationBathroom Waterproofing
Waterproofing is the step that decides whether a walk-in tub surround lasts 5 years or 25. We use cement backer board, a roll-on membrane, and sealed seams, then flood-test the pan before tile goes down. This is where cheap installs fail.
Bathroom WaterproofingBathroom Drywall and Painting
After a tub install, the walls around the surround need patching and paint. We hang greenboard in wet zones, tape and float the seams, and finish with a bathroom-rated paint. The room looks finished instead of half-done.
Bathroom Drywall and PaintingWhat Georgetown Customers Say
Real experiences from customers who chose our Walk-In Tub Installation services
"After my knee replacement I could not get into the old tub safely. The crew measured on a Tuesday and installed a walk-in tub with grab bars the following week. They pulled the permit, handled the inspection, and tiled the surround to match my floor. The door seal has not leaked once in eight months."
Martha R.
Homeowner, Sun City Georgetown
"We were remodeling the hall bath for my father-in-law and needed a walk-in tub fast. Georgetown Bath Remodel Pros gave us a written price, showed up on time, and finished in one day. They found soft wood under the old tub and replaced it instead of tiling over it. That honesty is why I would call them again."
David K.
Homeowner, Wolf Ranch
"Our 1970s bathroom had a cast iron tub and a slow drain. They cut it out, replaced the PVC drain pipe, and set a new walk-in tub with a tile surround. The plumber pressure-tested everything before they left. It took two days total and the bathroom looks like a different room."
Elaine P.
Homeowner, Old Town Georgetown
Schedule Your Walk-In Tub Installation Georgetown TX
We are a licensed, insured crew based in Georgetown, and we have been installing walk-in tubs here since 2013. Call 512 325 0295 to book a free measure and a written price. Most installs are scheduled within one to two weeks.