Bathroom Flooring Installation Georgetown TX
Waterproof tile floors built for Texas homes
Bathroom Flooring Installation Georgetown TX handles the whole job: tear-out, subfloor repair, waterproofing, and finished tile. We work in homes across Williamson County, from Old Town bungalows to Sun City builds, and we build floors that survive steam, splashes, and decades of foot traffic. If your floor is cracked, soft, or just dated, we can fix it.
Bathroom Flooring Installation Georgetown TX
Bathroom Flooring Installation Georgetown TX is the trade of removing an existing bathroom floor, correcting whatever the subfloor is hiding, and installing a new waterproof finished surface that drains, cleans, and lasts. That means pulling the toilet, cutting out old vinyl or tile, checking the plywood for rot, laying cement backer board or an uncoupling membrane, then setting ceramic or porcelain tile with proper thinset and grout. Every layer matters. Skip one and the floor fails in two winters.
Most Georgetown homeowners call us for one of three reasons: cracked or hollow-sounding tile, a floor that flexes near the toilet flange, or a remodel where the old sheet vinyl has finally given up. Homes in Sun City Georgetown and Berry Creek often still have original 1990s flooring, and slab movement around here opens grout lines fast. If you have been searching for bathroom flooring installation in Georgetown TX near me, we handle the full scope, including the plumbing disconnect and reset.
Why Replace a Bathroom Floor
A bathroom floor is the first surface to fail and the last one people replace. These are the four outcomes our Georgetown customers care about most.
Waterproof From Below
We install a waterproofing membrane over the substrate before a single tile goes down, so splashes and slow leaks never reach the framing. In a 40-square-foot bathroom, that membrane costs a fraction of what subfloor replacement runs after water damage.
Stops Subfloor Rot
Soft spots near the toilet or tub usually mean a leaking wax ring or a failed shower pan has been soaking the plywood for months. We cut out the damaged section, sister in new material, and reset the flange so the next leak has nowhere to hide.
Tile That Handles Humidity
Porcelain tile from Daltile or MSI absorbs under 0.5 percent moisture, which matters in a room that hits 90 percent humidity during a hot shower. It will not swell, peel, or cup the way sheet vinyl does after a few Texas summers.
Easier Cleaning, Fewer Stains
Grout lines sealed with a penetrating sealer resist mildew and hard-water staining. A 12x24 tile layout leaves fewer joints to scrub, and a squeegee once a week keeps the whole floor looking new for years.
How Our Floor Installation Process Works
Five steps, roughly two to four days for a standard hall bath. Here is exactly what happens from the first walkthrough to the final caulk line.
Walkthrough and Measure
We measure the room, check the subfloor with a moisture meter, and look at the toilet flange height. You get a written scope and a fixed price the same day, usually within 24 hours of your call. We also note whether the vanity needs to come out.
Demo and Haul-Out
We shut off the water, pull the toilet, and remove the old flooring down to the plywood or slab. A 50-square-foot bathroom takes about three hours. All debris leaves in our truck, so you are not renting a dumpster.
Subfloor Repair
Any soft or delaminated plywood gets cut out and replaced. We check the joists with a level, add blocking where the floor flexes, and set a new PVC drain pipe or flange if the old one is cracked. This is the step most cheap installs skip.
Waterproofing and Tile Set
We roll or sheet a waterproofing membrane, then set cement backer board where it is needed. Tile goes down with a wet saw for the cuts, tile spacers for the layout, and a grout float to finish. A 40-square-foot floor sets in one day.
Grout, Caulk, Reset
Grout cures overnight, then we caulk the perimeter with silicone caulk, reset the toilet with a new wax ring, and reinstall the vanity and baseboards. We walk the floor with you, check for lippage, and leave the room ready to use.
13 Years Flooring Georgetown Homes
Georgetown Bath Remodel Pros has been installing bathroom floors since 2013, which puts us at 13 years serving Williamson County. In that time we have torn out everything from 1970s mosaic tile near the Georgetown Square to builder-grade vinyl in Teravista. Our crews hold TDLR contractor licensing, and we follow TCNA guidelines for substrate prep and movement joints. We also carry EPA Lead-Safe Certification, which matters in pre-1978 homes around Old Town where old floor mastic can test positive for lead.
- TDLR-licensed contractor with crews trained on TCNA tile installation standards.
- EPA Lead-Safe Certified for pre-1978 homes in Old Town and San Gabriel Heights.
- More than 900 bathroom floors replaced across Williamson County since 2013.
- We pull permits when the scope touches plumbing or structural subfloor repair.
- Every install includes a moisture meter reading before we set a single tile.
Why Georgetown Homeowners Pick Our Flooring Crew
Bathroom flooring is a small job that goes wrong in expensive ways. We price it honestly, show up when we say, and stand behind the work with a written warranty.
Fixed Price, No Surprises
You get one number before we start. If we open the floor and find rot we did not see, we stop, show you the damage, and price the repair before touching it. No change orders after the fact, no hourly billing that creeps.
Two to Four Day Turnaround
A standard hall bath is a two-day job. Larger primary bathrooms with heated floors or intricate patterns run three to four days. We schedule back-to-back so you are not living without a working toilet for a week.
Plumbing Handled In-House
We pull the toilet, replace the flange, and reset the fixture ourselves under our Texas State Board of Plumbing Examiners license. You do not need to hire a separate plumber, which saves a service call and keeps one crew accountable.
Materials That Fit Texas
We stock porcelain tile from Daltile and MSI, Schluter waterproofing membranes, and silicone caulk rated for high-humidity rooms. Everything we install is rated for wet-area use, not just dry-floor tile sold at big-box stores.
What Our Bathroom Flooring Service Includes
Every floor replacement we do covers the full scope from demo to reset. Here is what is included in a standard install. If your project needs something outside this list, we will tell you upfront and price it separately before we start.
What's Included
Full Demo and Haul-Out
We remove the old flooring, underlayment, and any failed substrate down to sound material. All debris leaves in our truck. A standard 50-square-foot bathroom demo takes about three hours and leaves the room ready for prep.
Subfloor Inspection and Repair
We check the plywood or slab with a moisture meter and a level. Soft or delaminated sections get cut out and replaced. We add blocking where the floor flexes so the new tile has a stable base.
Waterproofing Membrane
A Schluter or comparable waterproofing membrane goes over the substrate before tile. We seal the perimeter, the toilet flange, and any penetrations so water that gets past the grout never reaches the framing.
Tile Set and Grout
We set ceramic or porcelain tile with the correct thinset for your substrate, using tile spacers for consistent joints. Grout goes in after the tile cures, followed by a penetrating sealer on the grout lines.
Toilet Pull and Reset
We shut off the water, pull the toilet, and reset it on a new wax ring after the floor is finished. If the flange is cracked or the shutoff valve leaks, we replace it during the same visit.
Final Caulk and Walkthrough
We caulk the perimeter with silicone caulk, reinstall baseboards and the vanity, and walk the floor with you. We check for lippage, verify the toilet seals, and leave the room ready to use that evening.
Bathroom Floor Problems We Fix in Georgetown
Most bathroom floor calls start with one visible symptom and end with a bigger repair underneath. Here are the four we see most often in Georgetown homes.
Cracked or hollow-sounding tile
Cracks let water into the substrate, which softens plywood and can rot the framing under the toilet within a season.
We cut out the failed tile and check the substrate for moisture. If the subfloor is sound, we can often replace the affected section. If it is soft, we replace the plywood, add blocking, and install new tile with a proper membrane underneath.
Soft floor near the toilet flange
A leaking wax ring soaks the subfloor every time the toilet is used. Left alone, the flange can drop and the toilet rocks, which makes the leak worse.
We pull the toilet, cut out the damaged plywood, sister in new material, and install a new PVC flange at the correct height. Then we waterproof the area and set new tile so the next leak has nowhere to go.
Mildew and musty smell after showers
Persistent mildew usually means poor ventilation, not a dirty floor. An exhaust fan that does not move air keeps humidity above 80 percent, which feeds mold in grout lines and behind baseboards.
We check the exhaust fan and duct, replace undersized units with a Broan or Panasonic fan sized to the room, and run the duct to the exterior. Then we install new tile and seal the grout so moisture has nothing to feed on.
Outdated vinyl or carpet in the bathroom
Sheet vinyl peels at the edges and traps water underneath. Carpet in a bathroom holds moisture and grows mildew, which affects air quality in the whole house.
We remove the old flooring, repair any water damage to the substrate, and install ceramic or porcelain tile with a waterproof membrane. The result is a floor that cleans with a mop and will not peel, cup, or hold odor.
When Georgetown Homeowners Replace a Bathroom Floor
A 1990s Sun City Georgetown bathroom with original vinyl flooring that has started to peel at the tub edge.
We remove the vinyl, check the plywood for water damage near the tub, and install porcelain tile with a waterproofing membrane. The toilet comes out and resets on a new wax ring during the same visit.
A floor that handles daily showers without peeling, and a subfloor that stays dry even if the tub splashes over.
An Old Town Georgetown bungalow with cracked mosaic tile and a toilet that rocks when you sit down.
We pull the toilet, cut out the failed tile and any soft plywood, and replace the flange at the correct height. New tile goes down over a repaired, level substrate with lead-safe practices in place.
A stable toilet, a level floor, and tile that matches the character of the house without the lead risk.
A Wolf Ranch home where the bathroom floor flexes near the shower curb and grout lines keep opening.
We inspect the joists, add blocking where the floor moves, and install a cement backer board over the repaired substrate. A Schluter membrane ties the floor into the shower pan so the two waterproofing planes connect.
A floor that stops moving, grout lines that stay closed, and a shower-to-floor transition that will not leak.
A rental property near Georgetown Square where the bathroom carpet has to go before the next tenant moves in.
We schedule a two-day install, remove the carpet and pad, seal the subfloor, and set durable ceramic tile with a dark grout that hides stains. The toilet resets the same day.
A rental-ready bathroom floor that mops clean, resists tenant wear, and will not need replacing for 20 years.
Tools and Methods We Use
Tools & Equipment
Wet Saw
Cuts porcelain and ceramic tile with a water-cooled diamond blade. It gives clean edges on every cut, including the tricky ones around the toilet flange and door jamb.
Moisture Meter
Reads the moisture content in plywood and slab before we install anything. If the reading is high, we find the source and fix it before tile goes down.
Oscillating Multi-Tool
Cuts out old caulk, trims the door jamb for tile clearance, and handles detail work around the toilet flange without damaging adjacent surfaces.
Grout Float
Pushes grout into the joints at a consistent angle so the lines fill evenly. We follow with a sponge to shape the joints before they cure.
Tile Spacers and Level
Keep the layout consistent and check that the floor is flat within 1/8 inch over 10 feet, which is the TCNA standard for tile installation.
Caulking Gun
Applies silicone caulk at the perimeter and around the toilet base. Silicone flexes with the floor and will not crack the way grout does at a change of plane.
Methods
TCNA Substrate Preparation
We follow Tile Council of North America guidelines for substrate flatness, movement joints, and bonding. That means checking the floor with a level, adding blocking where it flexes, and using the correct thinset for the substrate.
Schluter Waterproofing System
We install Schluter membranes over the substrate and seal every penetration. The membrane keeps water that gets past the grout from reaching the plywood, which is the single biggest cause of subfloor failure.
Cement Backer Board Over Plywood
For wood subfloors, we set cement backer board in a bed of thinset and screw it down. It gives the tile a dimensionally stable surface that will not expand and contract with humidity the way plywood does.
Epoxy Grout in Wet Zones
In showers and around the toilet, we can use epoxy grout instead of cement grout. It resists staining and does not need sealing, which makes it a good fit for high-traffic Georgetown bathrooms.
How Bathroom Flooring Works in Georgetown
Georgetown sits on expansive clay soil, and that matters for bathroom floors. The soil swells when it is wet and shrinks in drought, which moves slabs and opens grout lines in homes across Williamson County. In slab-on-grade houses, we check for cracks and use an uncoupling membrane to isolate the tile from slab movement. In pier-and-beam homes around Old Town and San Gabriel Heights, we check the joists for sag and add blocking where the floor flexes. Humidity is the other factor. Georgetown summers push indoor humidity past 60 percent, and a bathroom without a working exhaust fan will grow mildew on grout within a year. We size the fan to the room and run the duct to the exterior. If you are looking for affordable bathroom flooring installation Georgetown TX homeowners can count on, we build the waterproofing and ventilation into the scope so the floor lasts. We also handle lead-safe work in pre-1978 homes, which covers most of the housing stock near the Georgetown Square and Blue Hole.
Service Areas
Many homes here date to the 1940s and 1950s, so lead-safe practices and pier-and-beam subfloor repair are common parts of the scope.
Active-adult community with mostly slab-on-grade construction. We see a lot of original 1990s vinyl and tile that is ready for replacement.
Newer construction with wood subfloors. We often add blocking and a cement backer board to stop the flex that opens grout lines.
Golf-course community with larger primary bathrooms. Heated floors and 12x24 porcelain layouts are popular requests here.
Builder-grade tile from the 2000s is now failing at the edges. We replace it with porcelain and a waterproofing membrane underneath.
Local Considerations
Expansive clay soil movement
Slabs shift seasonally, which cracks tile and opens grout lines. We use an uncoupling membrane to isolate the tile from slab movement so the floor stays intact.
High summer humidity
Indoor humidity above 60 percent feeds mildew in grout and behind baseboards. We check the exhaust fan and duct on every job and replace undersized units.
Older pier-and-beam housing stock
Homes near the Square often have joists that have sagged over decades. We level the floor and add blocking before installing tile so the finished surface is flat.
Winter freeze events
Frozen pipes can burst and flood a bathroom floor. We check the supply lines and shutoff valves during the install and replace anything that looks stressed.
Sun City Vinyl to Porcelain
A 1996 Sun City Georgetown bathroom had original sheet vinyl that was peeling at the tub edge. The plywood underneath showed water staining near the toilet, and the flange was 1/4 inch below the finished floor.
We removed the vinyl, replaced 12 square feet of damaged plywood, and installed a Schluter membrane under 40 square feet of 12x24 porcelain tile. The flange was reset at the correct height and the toilet no longer rocks.
Maintenance & Follow-up
Sweep weekly, damp-mop with a pH-neutral cleaner, and reseal the grout every two years. Keep the exhaust fan running for 15 minutes after every shower.
A 1952 bungalow near the Georgetown Square had original 1-inch mosaic tile with cracked grout and a soft spot near the tub. The floor sloped about 3/4 inch across the room, and the mastic tested positive for lead.
We removed the mosaic under EPA Lead-Safe practices, sistered two joists, and leveled the floor with a self-leveling compound. New 2-inch hex tile matched the era, and the floor is now flat within 1/8 inch.
Maintenance & Follow-up
Use a soft-bristle brush on the hex grout lines and avoid acidic cleaners. Reseal the grout annually because the smaller joints collect more soap scum.
A 2015 Wolf Ranch home had grout lines opening along the shower curb within three years of the build. The floor flexed when you stepped near the shower, and the toilet had started to rock.
We added blocking between four joists, installed cement backer board over the repaired substrate, and set 55 square feet of porcelain tile with an epoxy grout in the wet zone. The floor no longer moves and the grout lines have stayed closed.
Maintenance & Follow-up
Epoxy grout does not need sealing. Wipe the floor with a microfiber mop and check the caulk line at the shower curb once a year for cracks.
How much does bathroom flooring installation cost in Georgetown TX?
Most Georgetown bathroom floor replacements run $1,200 to $4,500 in 2026, depending on square footage, tile choice, and whether the subfloor needs repair. A basic 40-square-foot ceramic install with no rot starts around $1,200. Porcelain, heated floors, or extensive subfloor work push it higher. We give you a fixed number after the walkthrough.
What is the best flooring for a Georgetown TX bathroom?
Porcelain tile is the best choice for Georgetown bathrooms because it handles humidity, resists staining, and lasts 30-plus years. Ceramic tile is a close second and costs less. Luxury vinyl plank works for budget projects but will not survive a slow leak the way tile does. We install all three and will tell you which fits your subfloor.
How long does bathroom flooring installation take in Georgetown Texas?
A standard hall bathroom takes two days: one for demo, subfloor prep, and waterproofing, and one for tile set and grout. Larger primary bathrooms with heated floors or complex patterns run three to four days. Grout needs 24 hours to cure before the toilet goes back on, so plan for one night without that fixture.
Do I need a permit for bathroom flooring installation in Georgetown TX?
A straight flooring swap usually does not require a permit in Georgetown. If the scope includes moving the toilet flange, replacing drain pipe, or repairing structural subfloor framing, the city requires a plumbing or building permit. We pull it for you and handle the inspection, which typically adds two to three days to the schedule.
Licensed, Insured, and Local
Certifications
Reviews
Replaced the floor in our Sun City bathroom in two days. They found soft plywood under the toilet, showed us the damage, and fixed it for the price they quoted. The tile work is clean and the grout lines are perfect.
We had three quotes and these guys were the only ones who mentioned waterproofing. They installed a membrane under the tile and sealed everything. Six months later, no cracks, no mildew. Worth every penny.
Old Town house with original mosaic tile. They handled the lead-safe requirements without drama and matched the era with new hex tile. The floor is level and the toilet no longer rocks. Highly recommend.
Fast, professional, and honest. They pulled the toilet, replaced a cracked flange, and installed new porcelain tile in our Wolf Ranch home. The floor stopped flexing and the grout lines have stayed closed.
Related Services
Full Bathroom Remodeling
A new floor is often the first domino in a full bathroom remodel. We coordinate flooring with vanity, shower, and lighting work so the whole room finishes on one schedule instead of three separate contractor visits.
Full Bathroom RemodelingBathroom Renovation
If your Georgetown bathroom is 20 years old, a renovation lets you fix the floor and the layout at once. We handle the demolition, framing changes, and finish work under one contract, which keeps the floor level with the new shower curb.
Bathroom RenovationShower Remodeling
Shower remodels and floor replacements go together because the shower pan and floor share a waterproofing plane. We tie the two together so water that escapes the shower never reaches your subfloor.
Shower RemodelingBathtub Remodeling
When we replace a tub, the floor around it usually needs work too. We reset the tub, repair any soft subfloor underneath, and install new flooring that meets the tub apron cleanly.
Bathtub RemodelingWalk-In Tub Installation
Walk-in tubs add weight and require a level, reinforced floor. We inspect the joists, add blocking where needed, and install flooring rated to handle the load and the splash zone around the door seal.
Walk-In Tub InstallationTile Installation
Bathroom floors are one tile application among many. We also install tile on shower walls, backsplashes, and fireplace surrounds, using the same wet saw, spacers, and grout float on every job.
Tile InstallationVanity Installation
A new vanity sits on the floor, so the two projects should be sequenced. We install the floor first, then set the vanity cabinet and reconnect the PEX supply lines and PVC drain.
Vanity InstallationBathroom Countertop Installation
Quartz and granite countertops pair well with new tile floors. We template the vanity top after the floor is set so the countertop sits at the correct height and the edges line up with the tile.
Bathroom Countertop InstallationToilet Installation
Every floor replacement includes pulling and resetting the toilet with a new wax ring. If the flange is cracked or the toilet is outdated, we can supply and install a Kohler, Toto, or American Standard model while the floor is open.
Toilet InstallationSink Installation
New floors often come with a new sink. We install undermount and drop-in sinks, connect the Moen or Delta faucet, and check for leaks before we caulk the backsplash.
Sink InstallationFaucet Installation
A leaking faucet dripping onto a new floor is a waste. We replace Moen and Delta fixtures during the same visit, check the supply lines, and test for drips before we close up the vanity.
Faucet InstallationShower Door Installation
New shower glass frames look best against a fresh floor. We install framed and frameless doors, seal the track with silicone caulk, and make sure the door swings clear of the new tile.
Shower Door InstallationBathtub-to-Shower Conversion
Converting a tub to a shower changes the floor footprint and the drain location. We handle the PVC drain rework, waterproof the new shower pan, and install flooring that meets the new curb.
Bathtub-to-Shower ConversionAccessible Bathroom Remodeling
Curbless showers and ADA-compliant layouts require a floor that slopes correctly to the drain. We build the slope into the substrate and install slip-resistant tile rated for wet areas.
Accessible Bathroom RemodelingBathroom Cabinets and Storage
New cabinetry sits on the floor, so the sequence matters. We install flooring first, then set cabinets and storage so the toe kick meets the tile cleanly and nothing gets cut around.
Bathroom Cabinets and StorageBathroom Ventilation and Exhaust Fan Installation
A Broan or Panasonic exhaust fan that actually moves air keeps humidity off your new floor. We size the fan to the room and run the exhaust fan duct to the exterior, not into the attic.
Bathroom Ventilation and Exhaust Fan InstallationBathroom Waterproofing
Waterproofing is the layer under your floor that nobody sees and everybody needs. We apply Schluter membranes and seal penetrations around the toilet flange and shower drain before tile goes down.
Bathroom WaterproofingBathroom Drywall and Painting
Floor replacement often means new baseboards and patched drywall. We hang greenboard in wet zones, patch where the old flooring met the wall, and paint before the final caulk line goes in.
Bathroom Drywall and PaintingWhat Georgetown Customers Say
Real experiences from customers who chose our Bathroom Flooring Installation services
"Our 1998 bathroom floor had cracked tile around the toilet and I was worried about what was under it. The crew pulled everything, found soft plywood, replaced it, and waterproofed before setting new porcelain. Two days, fixed price, no surprises. The floor is level and the grout lines are dead straight."
Karen M.
Homeowner, Sun City Georgetown
"We live in a 1950s house near the Square and the bathroom floor was original mosaic tile over a wood subfloor. They handled the lead-safe requirements without making it a big deal and installed new tile that matches the era. The toilet flange was cracked and they replaced it the same day."
David R.
Homeowner, Old Town Georgetown
"I got three quotes for bathroom floor replacement and Georgetown Bath Remodel Pros was the only one that mentioned waterproofing. They installed a Schluter membrane under the tile and sealed everything. Six months in, no cracks, no mildew, and the floor still looks brand new."
Priya S.
Homeowner, Wolf Ranch
Get Your Bathroom Flooring Installation Georgetown TX Quote
We give fixed pricing, show up on schedule, and back every floor with a written workmanship warranty. Call 512 325 0295 or request a walkthrough online and we will get you a number within 24 hours.