Bathtub Remodeling Georgetown TX Built To Last
Tub replacement, surrounds and waterproofing done by a local crew
Bathtub Remodeling Georgetown TX homeowners can count on starts with a straight answer about what your tub needs. We tear out failing surrounds, rebuild the wall with cement backer board and a waterproofing membrane, then set new tile and fixtures that hold up to Central Texas humidity. Whether you want a deeper soaking tub in Sun City or a clean tub replacement in Georgetown TX before you sell, we handle the whole job, start to finish.
What Bathtub Remodeling Georgetown TX Involves
Bathtub Remodeling Georgetown TX is a demolition-to-finish bathroom service that replaces or refinishes your tub, rebuilds the surround, and restores the waterproofing behind it. We pull the old tub and surround, inspect the framing and subfloor for rot, reroute or extend PEX piping and PVC drain pipe as needed, then install a new tub, cement backer board, a waterproofing membrane, and ceramic or porcelain tile. New caulk, grout, and a properly sized exhaust fan finish the job so moisture leaves the room instead of soaking into the walls.
Most Georgetown tubs we open up are 15 to 30 years old, and the failure is almost never the tub itself. It is the surround: cracked tile, crumbling grout, and greenboard that has been wicking water for years. Homes in Sun City Georgetown and Berry Creek often show mold and mildew behind the caulk line, and older houses near Old Town Georgetown still have cast iron tubs set into mortar beds. If you have been searching for a bathtub remodel near me Georgetown, that hidden water damage is usually the reason to stop waiting.
Why Georgetown Homeowners Replace Their Tubs
A tub remodel is not cosmetic for most of our customers. It fixes a leak, removes a hazard, or makes a bathroom usable again. Here is what changes when the work is done correctly.
Stop Hidden Water Damage
A failed surround leaks a little every shower. By the time you see staining on the ceiling below, the subfloor and framing are already soft. We open the wall, replace damaged material, and rebuild with a waterproofing membrane rated for wet areas, so the next 20 years of showers stay inside the tub.
Safer Entry And Exit
Standard tub walls run 14 to 16 inches high, which is a real fall risk for older knees and hips. A low-threshold tub or a walk-in conversion drops that step dramatically. For Sun City Georgetown residents, that single change often means showering without help again.
Fixtures That Actually Work
A leaking faucet or a shower valve that swings between scalding and cold is not a small annoyance. We install Kohler, Moen, and Delta valves with pressure-balancing cartridges, so water temperature stays steady and the drip stops. Most valve replacements take a single day.
Easy To Clean, Easy To Live With
Large-format porcelain tile with epoxy grout wipes down in under two minutes. No scrubbing grout lines with a toothbrush, no recurring mildew at the caulk joint. If you want an affordable bathtub remodel Georgetown TX buyers will notice at resale, this is the upgrade that shows.
How Our Tub Replacement Process Works
Five steps, one crew, and a clear timeline. Most tub-only projects run three to five working days once materials are on site, and we tell you the schedule before we start.
On-Site Assessment
We measure the alcove, check the tub drain and overflow, and run a moisture meter across the surrounding drywall. If the subfloor is soft or the framing is compromised, you hear it that day, not after demolition. You get a written scope and a fixed price before anyone swings a hammer.
Demo And Protection
We lay drop cloths and seal off the doorway with plastic to keep dust out of the rest of the house. The old tub, surround, and drywall come out with an oscillating multi-tool and pry bars. A typical tear-out takes four to six hours, and we haul everything away the same day.
Rough-In And Repairs
The drain and overflow get new PVC, and the valve body is set at the correct depth for the new trim. Any rotten framing or subfloor gets replaced. This is the step that decides whether the finished job lasts, so we do not rush it.
Waterproofing And Tile
Cement backer board goes up first, then a waterproofing membrane over the seams and corners. Tile is cut on a wet saw, set with tile spacers, and finished with a grout float. We use Daltile and MSI porcelain on most Georgetown jobs because it handles humidity without warping.
Final Trim And Walkthrough
New silicone caulk at the tub-to-tile joint, a fresh exhaust fan if yours is undersized, and a full water test. We run the shower for 15 minutes and check for leaks before we call it done. You get a walkthrough, a care sheet, and our workmanship warranty.
13 Years Of Bathroom Work In Georgetown
Georgetown Bath Remodel Pros has been remodeling Williamson County bathrooms since 2013, which puts us at 13 years in business as of 2026. Our crew holds a Texas State Board of Plumbing Examiners license for the plumbing side of every tub job, a TDLR contractor license, and EPA Lead-Safe Certification for the pre-1978 homes we still run into near the Georgetown Square. We have completed hundreds of tub replacements, from simple acrylic swaps in Wolf Ranch to full cast iron tear-outs in Old Town. Every job is inspected against IRC and TCNA standards before we close the wall.
- 13 years serving Georgetown, Texas and the surrounding Williamson County area since 2013.
- State-licensed plumbing contractor on staff for drain, valve, and supply line work.
- EPA Lead-Safe Certified for remodels in older homes near the Georgetown Square.
- TCNA-compliant waterproofing on every surround we build, no shortcuts.
- OSHA 30 trained crew, fully insured, working in occupied homes daily.
Why Our Bathtub Remodeling Georgetown TX Stands Out
Plenty of crews will swap a tub. Fewer will open the wall, fix what is behind it, and waterproof the surround so the next failure is decades away. That difference is the whole job.
Fixed Price, No Surprises
You get a written scope and a locked price before demolition. If we find rot behind the wall, we show you photos and quote the repair before doing it. No mystery line items at the end, no day-rate creep on a three-day job.
We Open The Wall
Cheap tub replacement in Georgetown TX often means a drop-in liner over whatever is already failing. We remove the surround, inspect the framing, and replace what is damaged. It takes longer and costs more, and it is the only way the finished job holds up.
Plumbing Done In-House
Our licensed plumber handles the valve, drain, and supply lines, so you are not coordinating two trades and hoping they agree on depth and rough-in. One crew, one schedule, one point of contact for the whole bathtub replacement and remodeling Georgetown project.
Local To Williamson County
We work Georgetown every week, from Teravista to Crystal Knoll. That means we know which neighborhoods have cast iron drains, which have slab-on-grade tubs, and what the city expects on a bathroom permit. You are not hiring a crew driving in from two counties away.
What Our Tub Remodel Package Covers
Every tub project we quote includes the demolition, the waterproofing, and the finish work as one scope. You are not hiring a demo crew, then a plumber, then a tile setter. Add-ons like glass doors, vanity replacement, or a new exhaust fan are quoted separately so you can see exactly what each one costs.
What's Included
Tub Removal And Disposal
We cut out and haul away the old tub, surround, and any damaged drywall. Cast iron tubs get broken down and carried out without dragging them through your door frames. Disposal is included in the quoted price.
New Tub And Drain
Supply and install of your chosen tub, plus a new PVC drain, overflow, and shoe gasket. We set the tub level and bed it properly so it does not flex or squeak underfoot.
Waterproofing System
Cement backer board, sealed seams, and a bonded waterproofing membrane over the entire wet area. This is the layer that keeps water out of your framing, and we do not skip it to save a day.
Tile And Grout
Porcelain or ceramic tile set with the correct thinset, spacers, and grout for wet areas. We seal the grout and caulk the tub-to-tile joint with silicone, not grout, so it flexes instead of cracking.
Plumbing Trim And Valve
New faucet, spout, and shower valve installed and tested. We pressure-test the lines and check for drips before closing the wall, and we set the valve depth for the trim you chose.
Final Cleanup And Test
Full water test, wipe-down, and debris removal. We walk you through the finished tub, show you the caulk lines and grout, and leave a care sheet for keeping it clean.
Tub Problems We Fix In Georgetown TX
Most tub calls start with one symptom and turn out to be something else. Here are the four we see most often, and what it takes to actually fix them instead of covering them up.
Cracked tile and failing grout around the tub
Water gets behind the tile every shower. Within a year or two the drywall and framing soften, and you start seeing stains on the ceiling below or a musty smell that never goes away.
We remove the failed tile and the wet substrate behind it, replace any damaged framing, then rebuild with cement backer board and a waterproofing membrane. New tile and epoxy grout go on top. The leak path is gone, not painted over.
Mildew that keeps returning at the caulk line
Recurring mildew means moisture is trapped, not just surface-level. Scrubbing it away does nothing if the exhaust fan is undersized or the surround is holding water behind the wall.
We check the exhaust fan airflow and duct routing, replace undersized units with a correctly sized Broan or Panasonic fan, and rebuild the surround so it dries between showers. Mildew stops coming back because the moisture source is fixed.
Leaking faucet or a shower valve that will not hold temperature
A dripping faucet stains the tub and wastes water. A valve that swings hot and cold is a scald risk, especially with kids or older adults in the house.
We replace the valve body and cartridge with a pressure-balancing unit from Kohler, Moen, or Delta, and install new supply lines and shutoffs. Temperature stays steady and the drip stops. Most valve jobs are done in a day.
Tub too high to step into safely
A 16-inch tub wall is a fall hazard for anyone with balance or knee issues. Many Georgetown homeowners stop using their own shower rather than risk a slip.
We install a low-threshold or walk-in tub, add blocking in the walls for grab bars, and finish the surround in slip-resistant tile. The step-over drops to a few inches, and the bathroom becomes usable again without help.
When To Call For A Tub Remodel
You are selling a Georgetown home and the master tub looks 25 years old.
We do a fast-turnaround tub replacement with a clean white surround and modern fixtures, scheduled around your listing timeline. Three to four days on site, no surprises.
The bathroom photographs well and stops being the room buyers subtract from their offer. Most sellers recoup a meaningful share of the cost at closing.
A parent or grandparent in Sun City Georgetown can no longer step over the tub wall.
We install a low-threshold or walk-in tub with a built-in seat, add wall blocking for grab bars, and finish the surround in textured, slip-resistant tile.
Showering becomes independent again, and the bathroom meets ADA-style clearance without looking institutional.
The tub surround has cracked tile and you keep finding mildew at the caulk line.
We tear out the surround, replace any wet substrate, rebuild with backer board and membrane, and set new porcelain tile with epoxy grout.
The moisture path is closed. No more recurring mildew, no more scrubbing grout, and no hidden rot spreading into the framing.
You want a bathtub remodel with new surround Georgetown TX buyers will read as updated.
We pair a new tub with large-format porcelain tile, a niche for products, and a new valve and trim, all in one scope and one schedule.
The room reads as a deliberate remodel rather than a patch job, and it holds up to daily use for years.
Tools And Methods We Use
Tools & Equipment
Wet saw
Cuts porcelain and ceramic tile cleanly, including the L-cuts around the valve and tub apron, without chipping the glaze or leaving ragged edges at the grout line.
Moisture meter
Reads moisture content in drywall and framing before we quote. It tells us whether the surround can stay or has to come out, which is the single biggest cost variable on a tub job.
Oscillating multi-tool
Cuts drywall and backer board tight to the tub and framing without damaging adjacent surfaces. It is how we open a wall cleanly instead of tearing it apart.
Grout float and tile spacers
Keeps grout lines consistent and fully packed. Even spacing is what makes a surround look professional, and it is what keeps water from finding a low spot.
Pipe wrench and hole saw
For drain and valve work. The hole saw cuts clean openings in backer board for the valve body and shower arm so the trim plate seats flat and seals.
Caulking gun
Applies silicone caulk at the tub-to-tile joint, which is the one joint that must flex. Grout there cracks within a year; silicone does not.
Stud finder and level
Locates framing for grab bar blocking and checks that the tub and surround are plumb and level before tile goes up. Out-of-level tubs leak at the apron.
Methods
TCNA waterproofing standards
We build every surround to Tile Council of North America guidelines: backer board, sealed seams, and a bonded membrane that ties into the tub flange. This is the standard an inspector checks and the reason our surrounds do not leak.
IRC-compliant framing and plumbing
Drain sizing, venting, and valve rough-in depths follow the International Residential Code. That keeps the work legal, inspectable, and compatible with the trim you chose, so nothing has to be redone later.
Pressure-balanced valve installation
We set every new valve with a pressure-balancing cartridge, which holds water temperature steady when someone flushes a toilet or runs a sink. It is a code requirement in most new work and a safety upgrade in older homes.
Silicone at wet joints, grout everywhere else
Grout goes on the field tile. Silicone goes at the tub-to-tile transition and inside corners, where movement is constant. Mixing those up is the most common cause of a surround that cracks and leaks within two years.
Full water test before sign-off
We run the shower for 15 minutes and inspect the drain, overflow, valve, and caulk lines before we call the job complete. If something seeps, we fix it that day, not on a callback.
How Tub Remodeling Works In Georgetown
Georgetown sits on clay-heavy soil and limestone, and that geology matters for bathroom work. Slab movement shows up as cracked tile and separated caulk joints, especially in homes built in the 1990s and 2000s around Wolf Ranch and Georgetown Village. Central Texas humidity also means an undersized exhaust fan will let mildew return within a season, so we size the fan to the room and verify the duct actually vents outside. Building stock varies widely here. Old Town Georgetown and the Georgetown Square area have homes with cast iron tubs and original greenboard, and we handle those under EPA Lead-Safe Certification. Sun City Georgetown and Cimarron Hills skew toward accessible remodels with low-threshold tubs and grab bar blocking. For a tub replacement in Parkside on the River or Teravista, the plumbing is usually PEX and the job moves faster. If you are weighing tub replacement in Georgetown TX cost against a full remodel, we will walk you through both numbers on site. Permits come from the City of Georgetown when the drain or valve moves, and we pull them and meet the inspector ourselves.
Service Areas
Mostly 55-plus residents, so low-threshold tubs, walk-in conversions, and grab bar blocking are the standard request. We keep the finish clean and accessible without making it look medical.
Older homes with cast iron tubs set in mortar and original greenboard behind the tile. Lead-Safe work practices apply, and cast iron removal takes extra time and labor.
Newer construction where the tub surround is often the first thing to fail. We typically find builder-grade backer board with no membrane, which is why the caulk line keeps cracking.
PEX supply lines and PVC drains make the plumbing side straightforward. Most jobs here are tub-to-shower conversions or a tub swap with upgraded tile and a new valve.
Homes with mature landscaping and original 1990s bathrooms. Cracked tile and mildew behind the caulk are common, and the framing often needs repair once the wall is open.
Local Considerations
Clay soil movement cracking tile and caulk joints
Seasonal ground movement stresses the tub-to-tile joint. We use silicone at that transition instead of grout so it flexes with the house rather than cracking.
High summer humidity and undersized exhaust fans
Moisture stays in the room after showers, feeding mildew. We size the fan to the cubic footage and confirm the duct terminates outside, not in the attic.
Older homes with cast iron drains and galvanized supply lines
Cast iron corrodes and narrows over time, slowing drainage. When we open the wall we inspect the drain and replace the section under the tub if it is failing.
Slab-on-grade construction common in Georgetown subdivisions
Drain relocation means cutting concrete, which adds cost and time. We tell you upfront when a tub-to-shower conversion will require slab work.
Sun City Tub Swap For Safety
A 1998 cast iron tub with a 16-inch wall, cracked ceramic tile, and no grab bar blocking in the walls. The homeowner had stopped using the shower because stepping over the wall felt unsafe.
New low-threshold tub with a 6-inch step-over, textured porcelain tile surround, and blocking installed for two future grab bars. Job took four working days. The water test ran clean on the first pass.
Maintenance & Follow-up
Wipe the surround with a mild bathroom cleaner weekly and re-caulk the tub joint every three to five years. Check the grab bar anchors once a year for tightness.
Cracked grout and a persistent mildew smell in a hall bathroom. The moisture meter read high across the entire back wall, and the greenboard behind the tile was soft to the touch.
Full tear-out, rotten framing and subfloor section replaced, new cement backer board and waterproofing membrane, new porcelain tile with epoxy grout, and a correctly sized Panasonic exhaust fan. Five days total.
Maintenance & Follow-up
Run the exhaust fan for 15 minutes after every shower and clean the fan grille twice a year. Epoxy grout needs only a damp wipe, no scrubbing.
A builder-grade tub the family never used, with a leaking faucet and a valve that swung between scalding and cold. The alcove was 60 inches wide and wasted on a tub nobody filled.
Converted to a tiled shower with a linear drain, new Moen pressure-balancing valve, a recessed niche, and frameless glass. Usable floor space increased by about 8 square feet. Six working days.
Maintenance & Follow-up
Squeegee the glass after each use and clean the linear drain cover monthly. Check the silicone at the floor transition once a year.
How much does a bathtub remodel cost in Georgetown TX?
Most tub-only remodels in Georgetown run $3,200 to $9,500 in 2026, depending on tub type, tile selection, and whether we find water damage behind the wall. A basic acrylic tub replacement with a new surround sits at the low end. Cast iron removal, custom tile, and plumbing relocation push it higher. We quote a fixed price after the on-site assessment, so you know the number before work starts.
How long does a tub replacement take in Georgetown Texas?
A standard tub replacement takes three to five working days once materials are on site. Day one is demo, day two is rough-in and repairs, days three and four are waterproofing and tile, and day five is trim, caulk, and the water test. Custom tile patterns, glass panels, or unexpected framing repairs can add a day or two. We give you the schedule in writing before we begin.
Can I replace a bathtub without removing tile in Georgetown TX?
Sometimes, yes. If the existing tile is sound and the waterproofing behind it is intact, we can cut the tub out through the drain wall and slide a new one in. That saves two to three days and roughly $1,200 to $2,500. But if the tile is cracked, the grout is failing, or the moisture meter reads high, leaving it in place just buries a problem. We test before recommending either path.
Do I need a permit for a bathtub remodel in Georgetown TX?
A straight tub-for-tub swap with no plumbing relocation usually does not require a permit. Moving the drain, changing the valve, or altering the wall framing does, and the City of Georgetown inspects that work. We pull the permit when it applies and handle the inspection. Skipping it can complicate a future home sale, so we do not cut that corner.
Licensed, Insured, And Local
Certifications
Reviews
Replaced a cast iron tub in our Old Town house. They handled the lead-safe requirements without making it a big deal, and the tile work is better than what was there originally. Fixed price, finished in five days, cleaned up every afternoon.
We had three quotes and these were the only ones who tested for moisture before pricing. Found soft drywall behind the tile, showed us photos, and quoted the repair before touching it. No surprise charges at the end.
Walk-in tub install for my mother in Sun City. They added blocking for grab bars even though we had not asked yet, which turned out to be exactly what we needed six months later. Professional and on schedule.
Tub-to-shower conversion in Teravista. They pulled the permit, met the inspector, and the glass door fit perfectly because they measured after the tile was set. Six days start to finish and the bathroom feels twice as big.
Other Bathroom Services We Handle
Full Bathroom Remodeling
When the tub is only part of the problem, a full remodel covers the floor, vanity, lighting, and layout at once. Most Georgetown homeowners who start with a tub replacement end up here when they see how much else is dated.
Full Bathroom RemodelingBathroom Renovation
A renovation updates finishes and fixtures without moving walls. If your tub is fine but the room feels tired, this is the lighter-touch path, and we can still swap the tub while we are in there.
Bathroom RenovationShower Remodeling
Many tub replacements turn into shower remodels once the homeowner realizes they never take baths. We build tiled showers with proper slope, linear drains, and glass, sized to the same footprint as the old tub.
Shower RemodelingWalk-In Tub Installation
For homeowners who need a low step-in threshold and a built-in seat, a walk-in tub solves the safety problem a standard tub creates. We handle the framing, plumbing, and surround so it looks intentional, not added on.
Walk-In Tub InstallationTile Installation
Tile is where a tub surround lives or dies. We set porcelain and ceramic with the right thinset, spacers, and grout for wet areas, and we waterproof behind it so the tile is not the only line of defense.
Tile InstallationVanity Installation
A new tub makes an old vanity look worse. We install and set quartz or granite countertop vanities with new faucets, matching the finish level of the tub surround so the room reads as one project.
Vanity InstallationBathroom Flooring Installation
Water that escapes the tub ends up on the floor. We install porcelain tile, luxury vinyl, or stone with proper subfloor prep, so the floor handles splashes and stays level underfoot.
Bathroom Flooring InstallationBathroom Countertop Installation
Quartz and granite countertops resist the moisture and cosmetics that destroy laminate. We template, cut, and set the top with the sink and faucet in one visit.
Bathroom Countertop InstallationToilet Installation
If we are already in the room, replacing a running toilet or a worn wax ring is a small add-on. New toilets use less water and eliminate the rocking and leaking that come with age.
Toilet InstallationSink Installation
Undermount and drop-in sinks both need a clean cut and a sealed rim. We set the sink, connect the drain and supply lines, and test for leaks before we leave.
Sink InstallationFaucet Installation
A leaking faucet wastes water and stains the tub. We install Kohler, Moen, and Delta faucets with new supply lines and shutoff valves, so future repairs are simple.
Faucet InstallationShower Door Installation
Frameless and semi-frameless glass doors finish a tub or shower remodel. We measure after tile is set, so the panel fits the opening without gaps or silicone patches.
Shower Door InstallationBathtub-to-Shower Conversion
If nobody in the house takes baths, converting the tub to a tiled shower gains usable space and eliminates the step-over. We handle the drain relocation, waterproofing, and glass.
Bathtub-to-Shower ConversionAccessible Bathroom Remodeling
Grab bars, curbless entries, comfort-height toilets, and blocking behind the walls for future hardware. We build bathrooms that work now and stay workable as mobility changes.
Accessible Bathroom RemodelingBathroom Cabinets and Storage
Tub remodels often free up wall space. We add linen cabinets, recessed niches, and shelving so towels and products have a home instead of piling on the tub ledge.
Bathroom Cabinets and StorageBathroom Ventilation and Exhaust Fan Installation
An undersized or clogged exhaust fan is why mildew keeps coming back. We size the fan to the room, run the duct to the exterior, and verify airflow with a test.
Bathroom Ventilation and Exhaust Fan InstallationBathroom Waterproofing
This is the layer nobody sees and everybody needs. We apply a bonded waterproofing membrane over cement backer board at every tub and shower, sealed at seams and corners.
Bathroom WaterproofingBathroom Drywall and Painting
After the tub goes in, the surrounding walls need patching and paint. We use moisture-resistant drywall and a bathroom-rated finish so the room looks complete, not half-finished.
Bathroom Drywall and PaintingWhat Georgetown Homeowners Say
Real experiences from customers who chose our Bathtub Remodeling services
"We had put off replacing the tub for two years because my husband could not step over the wall safely anymore. The crew pulled the old cast iron tub, found soft subfloor, replaced it, and set a low-threshold tub with tile that matches the rest of the bathroom. Four days total. The water test at the end sold me, they ran the shower a full 15 minutes and checked everything."
Marta R.
Homeowner, Sun City Georgetown
"Our surround had cracked tile and a mildew smell we could not get rid of. They opened the wall and showed me the greenboard behind it, soaked through. Replaced the framing, put up backer board and a membrane, then new porcelain tile. It has been through two summers of Georgetown humidity and there is not a spot of mildew anywhere."
Dale K.
Homeowner, Berry Creek
"We got three quotes for a tub replacement and these were the only ones who tested for moisture before quoting. The price was not the cheapest, but it was fixed and it did not move. They pulled the permit for the valve change, handled the inspection, and cleaned up every day before leaving. The new Moen valve holds temperature perfectly."
Priya S.
Homeowner, Teravista
Get Your Bathtub Remodeling Georgetown TX Quote
One call gets you a site visit, a fixed price, and a start date. We have been remodeling Georgetown bathrooms since 2013, and we will tell you straight whether your tub needs a swap or a full rebuild. Call 512 325 0295 today.