Bathroom Vanity Installation Georgetown TX done clean, level, and leak-free
New vanity, new counters, new storage, one tidy crew.
Bathroom Vanity Installation Georgetown TX homeowners can schedule without the mess starts with a free measure and a straight answer on price. We pull the old cabinet, check the shutoff valves and drain, set the new vanity level, and reconnect everything so your sink, faucet, and storage all work the way they should. Whether you are updating a 1990s builder-grade bath or squeezing a double sink into a tight Sun City layout, our team handles the whole job.
Bathroom Vanity Installation Georgetown TX, explained
Bathroom Vanity Installation Georgetown TX is the removal of an existing vanity cabinet and the fitting of a new one, including leveling, plumbing reconnection, countertop setting, and caulking. A vanity carries the sink, faucet, and most of your bathroom storage, so it has to sit flat, drain correctly, and stay dry at the wall. We check the moisture meter reading behind the old cabinet, replace any soft drywall with greenboard, and set the new unit on a level shimmed base before the counter goes down.
Most Georgetown homes we walk into are 15 to 30 years old, and the vanity is usually the first thing to fail. Particleboard swells, the caulk line at the backsplash cracks, and a leaking faucet drips into the cabinet until the base is mush. If you have been searching vanity replacement Georgetown TX because the doors no longer close or the counter is stained through, that is normal wear, not bad luck. We also see plenty of Sun City and Wolf Ranch homeowners who want a bathroom vanity install in Georgetown Texas with taller counters, soft-close drawers, and better lighting.
Why Georgetown homeowners upgrade the vanity first
The vanity is the highest-use surface in the bathroom and the cheapest major change you can make. Here is what a proper install actually gets you.
Storage that fits your life
A 48-inch vanity with two drawers and a tilt-out tray holds more than the 36-inch cabinet it replaces. We measure your wall, account for door swing and baseboard, and pick a depth that leaves you 21 inches of clear floor. Soft-close hinges and full-extension drawer glides come standard on most of the units we install.
No more leaks under the sink
We replace the shutoff valves, swap the old PVC drain pipe for new, and pressure-test the PEX supply lines before the cabinet goes back in. A leaking faucet or a slow drain that soaked the old cabinet base does not get a second chance. Every connection gets a fresh silicone caulk bead at the wall and counter seam.
A counter that survives daily use
Quartz countertop and granite countertop both hold up to toothpaste, hair dye, and hot curling irons. We cut the sink opening with a hole saw and set the bowl with a waterproof seal, so you are not chasing a drip into the cabinet six months later. Undermount and drop-in sinks both work with the vanities we stock.
Better light and ventilation
A taller vanity with a matching mirror changes how the room reads, and it is the right time to address an exhaust fan not removing steam. We can tie in a Broan or Panasonic fan on the same visit, vent it through the roof deck, and cut the mold and mildew problem off at the source.
How our vanity installation process runs
Five steps, one crew, and a bathroom you can use the same evening in most cases. Here is exactly what happens from the first call to the final walkthrough.
Measure and quote
We come out, measure the wall, check the shutoff valves, and look behind the old cabinet for water damage. You get a written price the same day, not a range that moves. Most single-vanity swaps in Georgetown land between $650 and $1,900 in 2026 depending on size, counter material, and whether the plumbing needs to move.
Protect and demo
We lay drop cloths, shut off the water, and pull the old vanity in one piece where the doorway allows. The shutoff valves get capped, the drain gets plugged, and we haul the old cabinet and counter to the curb or the dump trailer. Demo on a standard 36-inch vanity takes about 45 minutes.
Prep the wall and floor
We check the wall with a stud finder, replace any soft drywall with greenboard, and confirm the floor is flat within an eighth of an inch. If the old caulk line left a stain or the paint is peeling, we sand and spot-prime before the new cabinet goes in. This is the step that keeps the new vanity from rocking.
Set and connect
The new cabinet gets shimmed level, screwed to the studs, and the counter is set with a bead of silicone caulk. We reconnect the PEX supply lines and the PVC drain pipe, install the faucet and sink, and run hot and cold water for a full five minutes to check for drips. A double sink vanity installation Georgetown TX homeowners ask about adds about 90 minutes to this step.
Caulk, clean, walkthrough
We run a fresh silicone caulk bead at the backsplash and side seams, wipe down the counter, and walk you through the shutoff locations and care instructions. The bathroom is usable the same day. If we tied in a new exhaust fan or moved a light, we test those before we pack up.
Why Georgetown picks us for vanity installation
We are a local crew, not a franchise. That means the person who quotes your job is the person who shows up, and the phone number on this page rings in Georgetown.
Licensed and insured
We hold a TDLR contractor license and carry general liability plus workers comp. Every plumbing connection we make is done to Texas State Board of Plumbing Examiners standards. If you are comparing bids and one contractor cannot show you a license, that is the bid to drop.
Same-week scheduling
Most vanity installs get on the calendar within five to seven business days, and we can often fit a straight swap sooner. We give you a two-hour arrival window and call when we are 30 minutes out. No all-day waiting.
Upfront pricing, no surprises
You get one number before we start, and it covers labor, haul-away, caulk, and standard connections. If we open the wall and find rot or a cracked drain line, we stop, show you, and price the fix before touching it. That is how a vanity cabinet installation Georgetown project should run.
We fix what the last guy left
A lot of our work is cleaning up after a flipper or a rushed install. Crooked cabinets, unlevel counters, drain lines with no slope, and caulk smeared over a leak. We correct the rough-in, then set the new vanity so it stays put. If you searched vanity installation near me Georgetown after a bad experience, we hear that a lot.
What our vanity installation includes
Every vanity install we quote covers the full job, not just setting a cabinet against the wall. Here is what is in the price and what we treat as an add-on if your bathroom needs it.
What's Included
Removal and haul-away
We disconnect the old vanity, cap the shutoff valves, plug the drain, and carry the cabinet and counter out. The old unit goes in our trailer, not on your curb for the neighborhood to look at for a week.
Leveling and anchoring
The new cabinet gets shimmed flat, checked with a level front to back and side to side, and screwed into the wall studs. A vanity that rocks will crack the caulk line within a year, so this step is not optional.
Plumbing reconnection
We reconnect the PEX supply lines and the PVC drain pipe, install the faucet and sink, and run water for a full five minutes to confirm no drips at any joint. New shutoff valves are included when the old ones are seized.
Countertop and sink set
Quartz or granite counter goes down on a silicone caulk bed, the sink opening is cut to template, and the bowl is sealed. We check the drain slope so water empties fully instead of pooling in the bottom of the sink.
Caulk and finish
Fresh silicone caulk at the backsplash, side seams, and floor line. We clean the counter, wipe the floor, and walk you through the shutoff locations before we leave. The bathroom is ready to use that evening.
Vanity problems we fix in Georgetown
Most vanities do not fail suddenly. They rot from the bottom up while the doors still open and close. Here is what we run into most often and how we handle it.
Swollen particleboard cabinet base from a slow leak
The cabinet loses structural strength, the doors stop closing square, and mold and mildew start growing in the dark space under the sink. Left alone, the rot spreads into the subfloor.
We pull the cabinet, cut out any soft drywall, and check the subfloor with a moisture meter. New greenboard goes up, the leak source gets fixed, and the new vanity sits on a dry, flat base. Most jobs add $150 to $300 for the wall repair.
Counter stained or cracked at the sink rim
A cracked counter lets water into the cabinet below every time someone washes their hands. The damage is invisible until the base swells, and by then you are replacing the whole unit.
We replace the counter with quartz or granite, cut a fresh sink opening, and seal the rim with a waterproof bead. If the cabinet is still solid, a counter swap alone runs $450 to $900 and buys you another decade.
Vanity too short for the user
Standard 32-inch counters force taller users to bend at the waist every morning. Back strain, splashing, and a mirror that sits too low are the usual complaints we hear from Sun City and Wolf Ranch homeowners.
We install a 36-inch counter height, which is the comfort standard for most adults. For accessible remodels we build to ADA compliance at 34 inches with clear knee space. The change costs nothing extra on a new cabinet order.
No storage and a cluttered counter
When the vanity has one shelf and no drawers, everything ends up on the counter. The room reads messy, and the constant moisture on the counter shortens the life of the caulk and finish.
We size the new vanity to the wall and spec drawers, a tilt-out tray, and a linen tower if there is room. A 48-inch cabinet with two drawers typically adds 40 percent more usable storage than the 36-inch unit it replaces.
When Georgetown homeowners call us for a vanity
A 1990s builder-grade vanity in a Sun City home has water-swollen doors and a stained counter.
We measure the wall, confirm the drain center, and quote a 48-inch cabinet with a quartz top. The old unit comes out in one piece, the wall gets patched, and the new vanity goes in on a level base with fresh shutoff valves.
A dry, level vanity with soft-close drawers and a counter that wipes clean. Most jobs finish in one day and land between $1,100 and $1,700.
A Wolf Ranch couple wants a double sink vanity but the wall is only 58 inches wide.
We source a 55-inch double-sink unit, shift the drain about four inches, and reroute the supply lines so both bowls get hot and cold. The mirror and sconces get repositioned to match the new counter height.
Two sinks, no more morning traffic jam, and a cabinet that fits the wall without blocking the door. Budget runs $1,900 to $2,800 depending on the counter.
A Berry Creek homeowner has a leaking faucet that soaked the cabinet base over several months.
We open the cabinet, show the rot, and quote the vanity replacement plus new greenboard and a waterproofing membrane at the wall. The faucet and drain get replaced at the same time so the leak source is gone.
A dry cabinet base, a new faucet that does not drip, and a wall that will not grow mold behind the vanity. Total cost usually $1,400 to $2,200.
An Old Town Georgetown homeowner is converting a tub to a shower and wants to upsize the vanity while the room is open.
We handle the bathtub-to-shower conversion and the vanity on one schedule. The plumbing rough-in happens once, the wall gets closed up after both are set, and the tile and paint go on last.
A larger vanity, a walk-in shower, and one clean finish instead of two separate projects. Combined budget typically $6,000 to $11,000.
Tools and methods we use
Tools & Equipment
Wet saw
Cuts ceramic tile and porcelain tile for backsplashes and floors with a clean edge and no chipping. A wet saw is the only way to get a straight cut on a vanity backsplash that meets the wall.
Oscillating multi-tool
Trims the old caulk line, cuts the drain opening in the new cabinet back panel, and notches for supply lines without cracking the finish. It reaches spots a saw cannot.
Pipe wrench and hole saw
Pipe wrench breaks loose the old drain connections and shutoff valves. The hole saw cuts a clean opening in the new cabinet for the drain and supply lines so the back panel stays intact.
Level and stud finder
The level confirms the cabinet sits flat front to back and side to side. The stud finder locates the wall framing so we anchor the vanity into wood, not just drywall.
Moisture meter
Reads the moisture content in the drywall and subfloor behind the old vanity. If the reading is high, we know there is a hidden leak before we set a new cabinet over a wet wall.
Caulking gun
Lays a consistent silicone caulk bead at the backsplash, side seams, and floor line. A steady bead is what keeps water out of the cabinet joint for years.
Methods
IRC and IBC rough-in standards
We set the drain and supply lines to International Residential Code and International Building Code specs, which govern trap arm slope, venting, and fixture clearances. That is what an inspector checks, and it is what keeps the drain flowing without a gurgle.
TCNA tile and waterproofing practice
Tile Council of North America guidelines govern how we set backer board, apply waterproofing membrane, and space tile joints. Following TCNA practice on the vanity backsplash and floor means the tile stays bonded and the wall stays dry.
EPA Lead-Safe work practice
Homes built before 1978 may have lead paint under the old vanity area. Our EPA Lead-Safe Certification means we contain dust, use HEPA filtration, and clean up to the standard the law requires on older Georgetown homes.
PEX supply and PVC drain reconnection
We replace old supply lines with PEX piping and reconnect the drain with PVC drain pipe, glued and primed at every joint. PEX handles the temperature swings in a Texas attic better than the copper it usually replaces.
How vanity installation runs in Georgetown
Georgetown sits on limestone and clay, and the soil movement shows up inside the house as floors that are rarely dead flat. We check the floor with a level before setting any cabinet, because a vanity that rocks will crack the caulk line within a year. The older homes near the Georgetown Square and Old Town often have cast iron drain lines and copper supply, which we replace with PVC drain pipe and PEX piping during the install. Newer builds out at Wolf Ranch and Parkside on the River usually have PEX already, so the swap is faster. Summer humidity in Williamson County pushes bathroom moisture up, and a vanity with a poorly vented cabinet will grow mold on the back panel. We always check the exhaust fan and add a Broan or Panasonic unit if the old one is undersized. If you want affordable bathroom vanity installation Georgetown TX without cutting corners, the local detail work is where the value sits.
Service Areas
Most homes here were built between 1998 and 2010 with 36-inch builder-grade vanities. We replace them with 48-inch units and often add a comfort-height counter for easier daily use.
Pre-1978 homes near the Square may have lead paint under the old vanity. Our EPA Lead-Safe Certification means we contain the dust and clean up to the federal standard.
Newer construction with PEX supply lines and PVC drains already in place. Vanity swaps here are usually a one-day job with no plumbing relocation.
Larger bathrooms with room for a 60-inch double vanity. We often tie in a new exhaust fan on the same visit because the original units are undersized for the square footage.
Local Considerations
Expansive clay soil and slab movement
Floors in Georgetown homes are rarely perfectly level. We shim and level every cabinet before anchoring, which prevents the rocking that cracks caulk lines and loosens drawer glides.
High summer humidity in Williamson County
Bathroom moisture climbs from May through September. We check the exhaust fan and add ventilation if needed, which keeps mold and mildew off the new cabinet back panel.
Older cast iron and copper plumbing
Homes built before 1990 often have cast iron drain lines that scale up and copper supply lines that pinhole. We replace the visible sections with PVC drain pipe and PEX piping during the install.
Hard Georgetown municipal water
Hard water leaves scale on faucets and stains the sink bowl. We install faucets with ceramic cartridges that resist scale buildup and recommend a quartz countertop over porous stone for easier cleaning.
Sun City 36-inch swap to 48-inch
A 1998 particleboard vanity with swollen doors, a stained cultured marble top, and a slow drain that had soaked the cabinet base. The wall behind it had soft drywall and a faint mildew smell.
We pulled the old unit, replaced the drywall with greenboard, and set a 48-inch cabinet with a quartz countertop and a fresh undermount sink. New shutoff valves and a new PVC drain line. Total job time was one day and the price came in at $1,480.
Maintenance & Follow-up
Wipe the counter with a mild cleaner, run the exhaust fan for 15 minutes after showers, and check the caulk line at the backsplash once a year. Re-caulk if you see any gap.
A 42-inch single-sink vanity in a 58-inch alcove. Two adults sharing one sink every morning, with counter clutter and no drawer space. The existing drain was centered for a single bowl.
We shifted the drain about four inches, rerouted the supply lines, and installed a 55-inch double-sink cabinet with two drawers. New faucets on both bowls, quartz top, and repositioned sconces. Job ran two days and totaled $2,640.
Maintenance & Follow-up
Keep the drain screens clean on both bowls, check under the cabinet for drips once a month for the first year, and avoid standing water on the counter seam.
A leaking faucet had dripped into the cabinet for months. The base was soft, the back panel had black mold spots, and the drywall behind the vanity read high on the moisture meter. The homeowner thought the whole bathroom needed a remodel.
We replaced the faucet, cut out the damaged drywall, applied a waterproofing membrane, and installed a new 42-inch vanity with a granite countertop. Added a Panasonic exhaust fan on the same visit. Total cost was $1,950 and the room was usable the next morning.
Maintenance & Follow-up
Run the new exhaust fan during and after showers, check the faucet base for drips quarterly, and keep the cabinet doors open for an hour after cleaning to let moisture escape.
How much does bathroom vanity installation cost in Georgetown TX?
Most single-vanity installs in Georgetown run $650 to $1,900 in 2026, including labor, haul-away, and standard plumbing reconnection. The vanity itself is separate and ranges from about $300 for a stock 30-inch cabinet to $2,500 or more for a 60-inch double-sink furniture piece with a quartz top. Moving the drain or supply lines adds $400 to $900. A straight swap with no plumbing changes sits at the low end.
How long does vanity installation take in Georgetown Texas?
A standard single-vanity swap takes three to five hours, and your bathroom is usable the same day. A double sink vanity installation Georgetown TX homeowners schedule usually runs five to seven hours. If we are moving plumbing, adding a new exhaust fan, or replacing damaged drywall and flooring, plan on a full day or two. We give you a realistic window when we quote the job, not a best-case guess.
Can I replace a vanity without moving plumbing in Georgetown TX?
Yes, and that is the cheapest way to do it. If the new cabinet has the same width and the drain and supply lines land in the same spot, we reconnect to the existing rough-in and you skip the plumbing move entirely. The catch is that vanity sizes are not standard across brands, so a 36-inch cabinet from one maker may not line up with another. We measure the existing drain center before you buy anything.
Do I need a permit for vanity installation in Georgetown TX?
A straight vanity replacement with no plumbing relocation does not require a permit in most Georgetown residential cases. If we move the drain, add a supply line, or tie into a new exhaust fan duct, that work falls under the plumbing and mechanical code and does need a permit through the city. We pull it, schedule the inspection, and handle the paperwork so you are not chasing the city yourself.
Licensed, insured, and local
Certifications
Reviews
Quoted $1,150 for a 48-inch vanity with quartz and stuck to it. They replaced the shutoff valves and drain line without charging extra, hauled the old cabinet off, and the counter is dead level. Bathroom was usable the same evening. Would hire again.
Found rot behind our old vanity and showed us before quoting the repair. No pressure, no upsell. New greenboard, waterproofing, and a 42-inch cabinet with granite. Took one day. Fair price for the work.
We needed a double sink vanity in a tight 58-inch alcove. They sourced a 55-inch unit, moved the drain four inches, and repositioned the sconces. Two-day job, clean work, no mess left behind. Highly recommend for Georgetown homeowners.
Called about a leaking faucet that had soaked the cabinet. They came out same week, quoted the vanity replacement plus new drywall, and finished in one day. Also flagged the exhaust fan and gave us a price to fix it later. Honest crew.
Related Services
Full Bathroom Remodeling
A new vanity is often the first domino. If the tile, tub, and floor are all original, a full remodel lets us rough in the plumbing once and finish everything to the same standard instead of tearing into a fresh wall a year later.
Full Bathroom RemodelingBathroom Renovation
Renovation covers the cosmetic layer: paint, trim, lighting, mirrors, and hardware. We time the vanity install so the new cabinet is not sitting in a room full of drywall dust, and we match the mirror and sconce height to the counter.
Bathroom RenovationShower Remodeling
If your shower is leaking into the same wall as the vanity, fix the shower first. We waterproof with a Schluter membrane and cement backer board before the new vanity goes in, so you are not replacing a cabinet twice.
Shower RemodelingBathtub Remodeling
Refinishing or replacing a tub changes the floor plan around the vanity. We coordinate the tub work and the vanity install on the same schedule so the room comes back together in one pass instead of two.
Bathtub RemodelingWalk-In Tub Installation
Walk-in tubs need clear floor space and often a wider doorway. We plan the vanity size and placement around the tub footprint so the room stays usable and you keep storage without blocking the tub door.
Walk-In Tub InstallationTile Installation
Vanity backsplashes, floors, and shower walls all use the same crew. We cut ceramic tile and porcelain tile with a wet saw, set with tile spacers, and finish with a grout float for a consistent joint line across the whole room.
Tile InstallationBathroom Flooring Installation
A new vanity sits on the floor, so the flooring has to be flat and finished first. We install tile or LVP, let it cure, then set the cabinet on top so the base is not trapped behind a toe kick you cannot remove later.
Bathroom Flooring InstallationBathroom Countertop Installation
Counter and vanity are one decision. We template for quartz countertop or granite countertop, cut the sink opening, and set the top with a waterproof seal so the seam at the wall stays dry through years of daily use.
Bathroom Countertop InstallationToilet Installation
If the toilet is the same age as the old vanity, replace both while the room is torn up. We set the new toilet on a fresh wax ring, check the flange, and confirm no running toilet before the vanity goes back in.
Toilet InstallationSink Installation
Undermount, drop-in, and vessel sinks all mount differently. We cut the opening to the sink template, seal the rim, and set the drain so the bowl empties fully without standing water in the bottom.
Sink InstallationFaucet Installation
A new faucet on an old vanity is a waste. We install the faucet after the counter is set, connect the supply lines, and test for a leaking faucet at the base and the aerator before we call the job done.
Faucet InstallationShower Door Installation
Frameless shower glass changes how much light reaches the vanity. If you are adding a glass door, we plan the vanity lighting and mirror placement around the new sightline so the room does not feel dark.
Shower Door InstallationBathtub-to-Shower Conversion
Converting a tub to a shower frees up floor space that often lets you go up a vanity size. We handle the conversion and the vanity on one schedule so the plumbing rough-in is done once.
Bathtub-to-Shower ConversionAccessible Bathroom Remodeling
ADA compliance calls for a 34-inch maximum counter height and clear knee space under the sink. We build or modify the vanity to hit that spec, with lever handles and a roll-under design if a wheelchair needs to fit.
Accessible Bathroom RemodelingBathroom Cabinets and Storage
Sometimes the vanity is fine and you just need more room. We add linen towers, medicine cabinets, and side storage that match the existing cabinet finish and fit the wall without crowding the door swing.
Bathroom Cabinets and StorageBathroom Ventilation and Exhaust Fan Installation
A vanity install is the right time to fix poor ventilation. We run the exhaust fan duct through the roof deck, size the fan to the room, and cut the mold and mildew problem before it stains the new cabinet.
Bathroom Ventilation and Exhaust Fan InstallationBathroom Waterproofing
Waterproofing membrane behind the vanity wall and around the sink area stops slow leaks from rotting the cabinet base. We seal the wet zones before the new unit goes in, which is cheap insurance on a $1,500 install.
Bathroom WaterproofingBathroom Drywall and Painting
Pulling a vanity always damages the wall behind it. We patch, texture, and paint the full wall before the new cabinet goes back, so you are not looking at a half-painted stripe above the backsplash.
Bathroom Drywall and PaintingWhat Georgetown homeowners say
Real experiences from customers who chose our Vanity Installation services
"Our 1998 vanity had swollen particleboard and the doors would not shut. They measured on Tuesday, quoted $1,150 for a 48-inch cabinet with a quartz top, and installed the following Monday. The crew replaced both shutoff valves and the drain line without charging extra. Counter is level, drawers close soft, and they hauled the old one off. Exactly what they quoted."
Marta R.
Homeowner, Sun City Georgetown
"We wanted a double sink vanity but the wall was only 58 inches. They found a 55-inch unit that fit with room for the door swing and moved the drain about four inches. Took most of a day. Water ran clean, no drips under the cabinet three months later. Fair price and no upsell on stuff we did not need."
Dale W.
Homeowner, Wolf Ranch
"Called about a leaking faucet that had soaked the cabinet base. They came out, showed me the rot, and quoted the vanity replacement plus new greenboard on the spot. Finished in one day. They also noticed the exhaust fan was not pulling steam and gave me a price to fix it later. Honest crew, no pressure."
Priya N.
Homeowner, Berry Creek
Get your Bathroom Vanity Installation Georgetown TX quote
One call gets you a same-day written price, a two-hour arrival window, and a crew that has been installing vanities in Williamson County since 2013. We haul the old cabinet away and leave the bathroom usable the same day.