Bathroom Tile Installation Georgetown TX done right the first time
Waterproofed showers, level floors, grout lines that stay clean
Bathroom Tile Installation Georgetown TX is what we do every week, and it starts with what you never see: cement backer board, a full waterproofing membrane, and a moisture meter before a single tile goes down. Whether you're updating a 1990s shower in Sun City or tiling a new build in Parkside on the River, our crew handles shower tile installation Georgetown, floors, walls, and niches as one continuous job. We've been tiling Williamson County bathrooms since 2013.
Bathroom Tile Installation Georgetown TX: What the Job Actually Involves
Bathroom Tile Installation Georgetown TX is the trade of setting ceramic, porcelain, or natural stone over a properly prepped, waterproofed substrate so the finished floor and walls shed water instead of absorbing it. That means tearing out the old surface, checking the framing with a level and stud finder, hanging cement backer board, then rolling a waterproofing membrane over every seam, corner, and curb. Only after that do we lay out the pattern, cut with a wet saw, set with tile spacers, and grout with a float. A standard tub surround runs 45 to 90 square feet; a full walk-in shower with a bench and niche usually lands between 90 and 140 square feet.
Georgetown homeowners call us for three reasons. First, cracked or hollow-sounding tile that's been flexing over a bad substrate. Second, mold and mildew creeping along the caulk line because an exhaust fan isn't removing steam and moisture has nowhere to go. Third, a full bathroom tile install in Georgetown Texas tied to a bigger renovation, where the tile has to line up with a new vanity cabinet, quartz countertop, and shower glass. If you've been searching for tile installation near me Georgetown and getting nothing but franchise call centers, we're a local crew that shows up in a truck with a wet saw, not a clipboard.
Why Georgetown Homeowners Choose Proper Tile Work
Tile is one of the few bathroom upgrades that pays you back in durability, resale, and daily livability. Done wrong, it's the most expensive mistake in the room. Here's what a correct install actually buys you.
Water Stays Where It Belongs
A Schluter waterproofing membrane behind the tile keeps shower water out of your framing and drywall. Without it, a slow leak behind a wall can rot studs for years before you notice a stain on the ceiling below. We pressure-test the pan and inspect every seam before tile goes up.
Tile That Doesn't Crack
Cracked tile almost always means a moving substrate, not bad tile. We screw cement backer board into solid framing, tape and mud the joints, and use a moisture meter to confirm the slab or subfloor is dry enough to bond. That's why our floors hold up under foot traffic for decades.
Easy Cleaning, No Scrubbing
Porcelain tile with tight grout lines and silicone caulk at the wet seams wipes clean with a damp cloth. We seal grout on natural stone and recommend a pH-neutral cleaner so you're not on your knees with a brush every month fighting mildew.
Real Resale Value
A clean, well-tiled bathroom is one of the first things a buyer inspects in Williamson County. Updated tile reads as a maintained home. Outdated, cracked, or moldy tile reads as a project, and buyers price that in before they make an offer.
How Our Tile Installation Process Works
Every job follows the same five stages, whether it's a single shower or a full bathroom. You'll know what's happening each day and when the water gets shut off.
Walkthrough and Measure
We come out, measure the space, and look at what's behind the existing tile. We check for soft drywall, prior water damage, and whether the exhaust fan duct actually vents outside. You get a written scope and a fixed price before we start, usually within 48 hours of the visit.
Demo and Prep
Day one is tear-out. We pull the old tile, backer board, and any greenboard that's been compromised, then haul it away. Floors get protected, the water gets shut off at the fixture, and we inspect the framing and PEX piping while the wall is open.
Waterproofing
This is the stage that separates a 20-year shower from a 5-year one. We hang cement backer board, tape and mud the seams, then roll on a waterproofing membrane and install a bonded flange at the drain. The pan gets a flood test before anything else happens.
Layout and Setting
We dry-lay the pattern so cuts land where they should, then set tile with spacers and a level checking every course. A wet saw handles the cuts, a hole saw handles the valve and shower arm penetrations, and a grout float finishes the joints once the thinset cures.
Grout, Caulk, and Cleanup
We grout, then caulk the wet seams with silicone caulk instead of grout so movement doesn't crack the joint. Fixtures go back on with a pipe wrench and caulking gun, we test the shower, and we sweep the room clean. Most jobs wrap in 3 to 6 working days.
Why Georgetown Picks Us for Bathroom Tile Installation
Tile is a finish trade, but the failures happen underneath. We build for the underneath. Here's what that looks like in practice.
Fixed Price, No Surprises
You get one number before demo starts, and it doesn't move unless you change the scope. If we open a wall and find rot or a leaking faucet behind the tile, we stop, show you, and quote the fix before touching it. No mid-job invoices you didn't approve.
Waterproofing Is Standard
Every shower and tub surround we build gets a full membrane, not just backer board and hope. That's the difference between a shower that lasts the life of the house and one that starts growing mold behind the wall in three years.
Local Crew, Local Codes
We know what Williamson County inspectors look for on a bathroom tile contractor Georgetown TX permit, and we know the older housing stock around Georgetown Square where greenboard was standard and needs replacing. No out-of-town subcontractors learning your neighborhood on your dime.
We Handle the Whole Room
Tile rarely happens alone. If you need a vanity cabinet set, a Kohler or Toto toilet swapped, a Moen faucet installed, or a Broan exhaust fan ducted properly, we do it in the same visit. One crew, one schedule, one point of contact from demo to final caulk.
What's Included in Our Tile Installation Service
Every tile job we quote includes the prep work that makes the finish last, not just the tile you see. Here's what's in the standard scope, and what we quote separately if your bathroom needs it.
What's Included
Demo and Haul-Away
We remove the old tile, backer board, and any compromised drywall or greenboard, then haul it off. Floors and fixtures get protected before the first hammer swings.
Substrate and Backer Board
New cement backer board screwed into solid framing, joints taped and mudded, and a moisture meter check on the subfloor before we set anything. This is the layer that keeps tile from cracking.
Waterproofing Membrane
A full rolled membrane over the shower walls, pan, and curb, with a bonded flange at the drain. We flood-test the pan before tile goes up so a slow leak never gets buried behind the wall.
Tile Setting and Cutting
Layout, dry-fit, and setting with spacers and a level on every course. A wet saw handles straight cuts, a hole saw handles valve and shower arm penetrations, and we keep the pattern aligned across walls and floor.
Grout, Caulk, and Sealing
Grout floated into the joints, silicone caulk at every wet seam, and sealer on natural stone or porous grout. We use caulk instead of grout at corners so movement doesn't crack the joint.
Fixture Reset and Cleanup
Shower valves, trim, and drains go back on with a pipe wrench and caulking gun. We test the shower, wipe down the room, and walk you through the finished job before we leave.
Bathroom Tile Problems We Fix in Georgetown
Most tile calls start with something visible and end with something hidden. Here are the four we see most often in Georgetown bathrooms, and what we do about each.
Cracked or hollow-sounding tile on the shower floor
Water gets behind the tile and into the pan, where it rots framing and shows up as a stain on the ceiling below months later.
We pull the affected tile, inspect the pan and substrate, and rebuild with new backer board and membrane. If the drain or PEX piping is compromised, we coordinate with a licensed plumber before re-tiling.
Mold and mildew along the caulk line and grout
It spreads into the grout and backer board, and the smell lingers even after cleaning. Left alone, it eats the substrate from the inside.
We remove the affected caulk and grout, treat the substrate, and check the exhaust fan. If the fan isn't removing steam, we replace it with a properly ducted Broan or Panasonic unit before re-tiling.
Tile popping loose or lifting at the edges
Usually a sign of a bad bond over drywall or greenboard that absorbed moisture. Once one tile goes, the rest follow.
We tear out the loose tile, replace the substrate with cement backer board, and re-set with proper thinset. This is the fix that stops the cycle instead of patching it.
Grout lines that stay dark no matter how you clean them
Stained grout is often the first sign that moisture is sitting in the joint instead of draining away, and it makes the whole bathroom look tired.
We regrout, seal with a penetrating sealer, and check the floor slope toward the drain. If the slope is off, we correct it during the re-tile so water actually leaves the shower.
When Georgetown Homeowners Call Us for Tile
A 1990s Sun City shower with original greenboard behind the tile and a fan that vents into the attic.
We tear out the shower to the studs, replace the greenboard with cement backer board and membrane, and re-duct the exhaust fan outside. Tile goes up after the pan passes a flood test.
A shower that drains properly, a bathroom that stays dry, and no more mildew smell within a week of use.
A Wolf Ranch new build where the builder-grade tile is cracking at the floor seams after two years.
We inspect the subfloor, correct the deflection, and re-set the floor tile over a properly prepped substrate with a crack-isolation membrane at the seams.
A floor that stays flat and crack-free through Texas summer humidity swings and normal family traffic.
A Georgetown Village rental where the tenant reported a leaking faucet and water staining on the wall behind the vanity.
We open the wall, replace the Moen cartridge and valve body, repair the drywall, and tile the backsplash and floor while the wall is open.
The leak is fixed at the source, the wall is dry, and the unit is ready for the next tenant in under a week.
An Old Town bungalow where the homeowner wants a walk-in shower instead of the original tub.
We handle the bathtub-to-shower conversion, coordinate the drain relocation with a licensed plumber, frame and waterproof the new pan, and set slip-resistant floor tile.
A modern walk-in shower that fits the footprint of the old tub and passes inspection without a framing change.
Tools and Methods We Use on Every Tile Job
Tools & Equipment
Wet Saw
Cuts porcelain, ceramic, and stone cleanly without chipping the glaze. Essential for 12x24 tiles and any cut that lands against a wall or door frame.
Tile Spacers and Level
Keep grout lines uniform and every course flat. A level on each row catches a low spot before the thinset cures, not after.
Grout Float and Caulking Gun
Pushes grout fully into the joints and lays a clean bead of silicone caulk at every wet seam. The caulk line is what keeps water out of the corners.
Moisture Meter
Confirms the subfloor or slab is dry enough to bond before we set tile. Skipping this step is how floors crack six months later.
Oscillating Multi-Tool and Hole Saw
Cuts clean openings for shower valves, shower arms, and grab bar blocking without cracking the surrounding tile.
Stud Finder and Pipe Wrench
Locates framing for grab bar blocking and tightens valve bodies and drain connections so nothing leaks behind the finished wall.
Methods
TCNA Guidelines
We install to Tile Council of North America standards for substrate, membrane, and movement joints. That's the reference Williamson County inspectors use, and it's the reason our showers pass on the first walkthrough.
Bonded Flange Drain Assembly
The drain flange bonds directly to the waterproofing membrane so water can't slip between the pan and the drain body. It's the detail that separates a 20-year shower from a 5-year one.
Flood Test Before Tile
We fill the pan and let it sit before a single tile goes down. If there's a pinhole in the membrane, we find it while the wall is still open, not after the shower is finished.
Silicone at Wet Seams
Corners, curb-to-wall joints, and tub-to-tile seams get silicone caulk, not grout. Grout is rigid and cracks with movement; silicone flexes and stays sealed.
How Tile Installation Runs in Georgetown, Texas
Georgetown sits in Williamson County, where the climate swings from 100-degree July afternoons to occasional hard freezes in January. That swing matters for tile. Grout and thinset expand and contract with the temperature, and showers that aren't waterproofed properly will show it within a few seasons. We build with that in mind, using cement backer board instead of greenboard, a full membrane instead of a paint-on sealer, and silicone caulk at every wet seam. The other local factor is housing stock. Homes near Georgetown Square and Old Town date back decades, and many still have original drywall behind the tile. Newer builds in Wolf Ranch, Berry Creek, and Parkside on the River have their own issues, usually builder-grade tile set over a subfloor that wasn't leveled. We check the substrate on every job, whether it's a 1970s bungalow or a 2022 build. For bathroom tile installation in Georgetown TX near me searches, we're usually within 15 minutes of the address, which means we can walk the job, quote it, and start on a schedule that works for you. ZIP codes 78626, 78628, and 78633 cover most of our work.
Service Areas
Many homes here have original 1990s tile and greenboard. We replace both as part of the standard scope, not as an add-on.
Older bungalows often have irregular framing behind the tile. We shim and level before backer board goes up so the finished wall is flat.
Newer construction with builder-grade tile. We typically correct subfloor deflection and re-set with a crack-isolation membrane.
A mix of owner-occupied and rental homes. We handle both, with quick turnarounds for rental turnovers.
New builds where the tile is fine but the exhaust fan often vents short. We re-duct while the wall is open.
Local Considerations
High summer humidity and 100-degree heat
Grout and thinset cure faster in July, so we adjust mix ratios and set smaller batches. It also means exhaust fans have to work harder, which is why we check the duct on every job.
Occasional hard freezes in winter
Pipes in exterior walls can freeze and burst behind tile. We inspect PEX and PVC drain pipe while the wall is open and flag anything that looks vulnerable.
Expansive clay soils in Williamson County
Slab movement can telegraph through a tile floor. We use a crack-isolation membrane on slab-on-grade floors to absorb that movement instead of cracking the tile.
Older homes with original drywall behind tile
Drywall absorbs moisture and loses its bond. We replace it with cement backer board as part of the standard scope, not as an upgrade.
Sun City Shower Rebuild with Membrane
A 2004 shower with cracked floor tile, mold along the caulk line, and greenboard behind the walls that had gone soft. The exhaust fan was venting into the attic, so steam had nowhere to go.
Full tear-out to the studs, new cement backer board, a rolled waterproofing membrane, and a bonded flange drain. New 12x24 porcelain walls with a hex mosaic floor. Fan re-ducted outside. Job took 6 working days.
Maintenance & Follow-up
Wipe the walls with a squeegee after each shower, run the fan for 15 minutes after, and clean grout with a pH-neutral cleaner once a month. No sealing needed on porcelain.
Builder-grade 12x12 ceramic floor tile cracking along the seams two years after move-in. The subfloor had a low spot near the toilet that was flexing underfoot.
We pulled the old tile, leveled the subfloor, installed a crack-isolation membrane, and set 12x24 porcelain in a running bond pattern. Toilet was reset on a new wax ring. Job took 4 days.
Maintenance & Follow-up
Sweep or vacuum regularly to keep grit off the surface, damp-mop with a neutral cleaner, and avoid harsh acid cleaners that dull the grout.
A rental with a leaking Moen faucet, water staining on the vanity wall, and 1990s tile that was chipped at the edges. Tenant had moved out and the unit needed to be rent-ready in two weeks.
We replaced the faucet cartridge and valve body, repaired the drywall, and tiled the backsplash and floor with a neutral porcelain. Unit was rent-ready in 7 working days, tenant moved in the following week.
Maintenance & Follow-up
Check the faucet and supply lines annually, reseal the backsplash grout every two years, and keep the exhaust fan clean so moisture doesn't sit on the tile.
How much does bathroom tile installation cost in Georgetown TX?
Most Georgetown bathroom tile jobs run $1,800 to $6,500 in 2026, with a typical tub surround landing near $2,400 and a full walk-in shower with bench and niche closer to $5,200. Price depends on square footage, tile choice, whether the substrate needs rebuilding, and whether fixtures move. We quote a fixed number after the walkthrough, not a per-square-foot guess.
What type of tile is best for Georgetown TX humidity?
Porcelain tile is the best all-around choice for Georgetown humidity. It absorbs under 0.5% water, handles the summer swings from 95-degree afternoons to air-conditioned evenings, and won't stain or etch the way natural stone can. Ceramic works fine on walls. For shower floors, we use a smaller porcelain or mosaic so the tile grips underfoot and the slope to the drain stays true.
How long does tile installation take in Georgetown Texas?
A tub surround takes 3 to 4 working days. A full walk-in shower with waterproofing, bench, and niche takes 5 to 7. A complete bathroom floor and shower together usually runs 7 to 10 days. Thinset needs 24 hours to cure before grout, and grout needs another 24 before the shower is used, so the calendar is real, not padded.
Do I need a permit for tile installation in Georgetown TX?
Straight tile replacement over an existing, sound substrate usually doesn't require a permit. If the scope includes moving a drain, relocating a valve, adding a shower pan, or reconfiguring plumbing, it does, and the work has to be done by a Texas State Board of Plumbing Examiners licensed plumber. We tell you at the walkthrough whether your job triggers one and handle the paperwork.
Licensed, Certified, and Local Since 2013
Certifications
Reviews
Rebuilt our Sun City shower from the studs out. Showed us the rotted greenboard before they started, waterproofed properly, and finished in six days. Grout still looks new a year later.
Tiled our Wolf Ranch bathroom floor and shower. Fixed a low spot in the subfloor we didn't know about. Clean crew, fair price, no surprises on the invoice.
Handled a rental turnover in Georgetown Village. Replaced a leaking faucet, tiled the backsplash and floor, and had it rent-ready in a week. Will use again.
Converted our Old Town tub to a walk-in shower. Coordinated the plumber, waterproofed the pan, and set slip-resistant floor tile. Passed inspection first time.
Other Bathroom Services We Handle
Full Bathroom Remodeling
Tile is usually the biggest line item in a full bathroom remodel, and we sequence it so the shower, floor, and walls all line up with the new vanity and lighting. One crew handles demo through final caulk in Georgetown.
Full Bathroom RemodelingBathroom Renovation
A renovation often means new tile over old framing. We open the walls, replace compromised greenboard and drywall, and set tile on a substrate that will actually hold it for the next 20 years.
Bathroom RenovationShower Remodeling
Shower remodeling and tile work are the same job in most Georgetown homes. We rebuild the pan, waterproof the walls, and set the tile so the shower drains properly and stays mold-free.
Shower RemodelingBathtub Remodeling
When a tub stays but the surround goes, we tile the walls, replace the valve trim, and caulk the tub-to-tile seam with silicone so water can't wick behind the wall.
Bathtub RemodelingWalk-In Tub Installation
Walk-in tubs need a level, waterproofed surround and a properly sloped floor. We set the tile after the tub is in place so the finished edges are clean and the door swing clears.
Walk-In Tub InstallationVanity Installation
We set the vanity cabinet, level it, then tile the floor and backsplash around it. Doing both in one visit means no gaps, no cut tile against a crooked cabinet, and no second crew.
Vanity InstallationBathroom Flooring Installation
Floor tile is where substrate prep matters most. We check the subfloor with a moisture meter, level it, and set porcelain or ceramic so it doesn't crack over the years.
Bathroom Flooring InstallationBathroom Countertop Installation
Quartz and granite countertops sit better when the vanity is level and the backsplash tile is set to meet them cleanly. We coordinate both so the seam line is straight.
Bathroom Countertop InstallationToilet Installation
Pulling a toilet to tile underneath is standard practice. We remove the fixture, tile the full floor, then reset the toilet on a new wax ring so there's no cut tile hiding behind the base.
Toilet InstallationSink Installation
New sinks and vanities often mean new tile behind them. We set the backsplash after the sink is in so the cutouts for supply lines and the drain are clean and sealed.
Sink InstallationFaucet Installation
A leaking faucet behind tile is a slow disaster. We replace Moen, Delta, and Kohler fixtures while the wall is open, then tile over a properly sealed valve body.
Faucet InstallationShower Door Installation
Frameless shower glass needs tile edges that are plumb and true. We set the tile with the door in mind so the hinges land on solid, level surfaces and the seal is watertight.
Shower Door InstallationBathtub-to-Shower Conversion
Converting a tub to a shower means a new pan, new drain location, and full waterproofing. We handle the plumbing coordination and tile the new shower as one continuous scope.
Bathtub-to-Shower ConversionAccessible Bathroom Remodeling
ADA-compliant showers need slip-resistant tile, proper slope, and grab bar blocking behind the walls. We install the blocking before tile so bars anchor into framing, not drywall.
Accessible Bathroom RemodelingBathroom Cabinets and Storage
Niche and recessed storage in a tiled shower has to be waterproofed like the rest of the wall. We frame, membrane, and tile the niche so it drains and never grows mildew.
Bathroom Cabinets and StorageBathroom Ventilation and Exhaust Fan Installation
Tile fails when steam has nowhere to go. We install or replace Broan and Panasonic exhaust fans and duct them outside so moisture leaves the room instead of soaking the grout.
Bathroom Ventilation and Exhaust Fan InstallationBathroom Waterproofing
Waterproofing is the layer under the tile, and it's the single biggest factor in how long the tile lasts. We roll membrane over backer board, tape seams, and flood-test the pan.
Bathroom WaterproofingBathroom Drywall and Painting
Tile stops where drywall begins. We patch, texture, and paint the surrounding walls after tile is set so the transition line is crisp and the room looks finished.
Bathroom Drywall and PaintingWhat Georgetown Clients Say About Our Tile Work
Real experiences from customers who chose our Tile Installation services
"Our 2004 shower had mold along the caulk line and two cracked tiles on the bench. Georgetown Bath Remodel Pros tore it out, showed me the rotted greenboard behind it, and rebuilt the whole thing with a membrane I could actually see before they tiled. Six months in, no mildew, no cracks, and the grout still looks new."
Marcy T.
Homeowner, Sun City Georgetown
"We had three quotes for a full bathroom floor and shower tile job. These guys were the only ones who talked about the substrate and the exhaust fan, not just the tile pattern. They finished in eight days, cleaned up every night, and the floor is dead level. Worth every dollar."
David R.
Homeowner, Georgetown Village
"We needed affordable bathroom tile installation in Georgetown TX for a rental property and didn't want to cut corners. They set 12x24 porcelain in the shower and a hex mosaic on the floor, replaced the leaking faucet while the wall was open, and handed it back on schedule. Tenant moved in the next week."
Priya N.
Homeowner, Wolf Ranch
Get Your Bathroom Tile Installation Georgetown TX Quote
We've been tiling Georgetown bathrooms since 2013, and we'll give you a fixed price after a walkthrough, not a phone guess. Call 512 325 0295 and we'll schedule a time to look at your shower, floor, or full bathroom.