Bathroom Faucet Installation Georgetown TX Done Right
Leak-free fixtures, honest pricing, and same-week scheduling
Bathroom Faucet Installation Georgetown TX homeowners can count on starts with a proper shutoff, clean supply lines, and a fixture set level on the deck. We handle faucet replacement Georgetown TX wide, from Old Town bungalows to Sun City villas, in two to four hours with no drips and no surprises. If your tap runs, sticks, or sprays sideways, we can fix it this week.
Bathroom Faucet Installation Georgetown TX Explained
Bathroom Faucet Installation Georgetown TX is the removal of an old or failing tap and the fitting of a new one, including shutoff valves, supply lines, drain assembly, and a water-tight seal at the deck or wall. We cut the water, drain the lines, and check the cabinet floor for moisture before anything new goes in. Most jobs involve one sink, but we also handle widespread, centerset, and single-hole setups, plus shower faucet installation Georgetown when the valve body needs swapping too.
Georgetown homes built between the 1970s and the 2000s are the ones we see most. Original valves seize, cartridges wear out, and hard water leaves scale that eats rubber seats. If you have been searching faucet installation near me Georgetown and getting thin quotes, we give you a real number before we start. We also replace the shutoff while we are under the cabinet, so the next repair is a five-minute job instead of a flood.
Why Upgrade Your Bathroom Faucet
A new faucet is one of the cheapest ways to change how a bathroom feels and works. Here is what you actually get when we swap it out.
Stop Paying for Drips
A tap that drips once per second wastes roughly 3,000 gallons a year, and on Georgetown water rates that adds up. A new cartridge or a full faucet replacement Georgetown TX stops the loss at the source. You will hear the difference the first night.
Better Water Pressure
Old aerators clog with mineral scale, and worn cartridges choke flow. We clear the line, fit a new fixture rated for 1.2 to 1.5 gallons per minute, and test pressure at the spout. Most customers see a noticeable jump at the sink within the same visit.
Fewer Emergency Repairs
We replace the angle stops and supply lines while the cabinet is open. That single step prevents the most common cause of bathroom water damage we get called for. It takes about 20 extra minutes and costs far less than a drywall and flooring repair.
Cleaner, Safer Water
Corroded brass and degraded rubber washers shed material into the stream. New PEX supply lines and a fresh fixture remove that path. If your home was built before 1988, we also check for lead solder at the stub-outs and flag anything that needs attention.
How Our Faucet Installation Process Works
Five steps, one visit for most jobs, and a clean cabinet when we leave. Here is exactly what happens from the phone call to the final test.
Phone Walkthrough
You describe the fixture, the sink, and what it is doing. We ask about shutoff valve condition and cabinet access, then give you a price range on the spot. If we need a photo, we ask for one by text. Most calls take under ten minutes.
Shutoff and Drain
We kill the water at the angle stops or the main, open the faucet to bleed pressure, and place a pan under the trap. The old supply lines come off first. If a shutoff will not close, we replace it before continuing, which is common in homes with 20-year-old valves.
Removal and Deck Prep
We pull the old faucet, scrape old silicone caulk and plumber's putty from the deck, and check the countertop for cracks or soft spots. A moisture meter goes on the cabinet floor. If we find rot or a failing quartz countertop edge, we tell you before we set the new fixture.
Install and Seal
New supply lines go on, the fixture is set level, and the drain assembly is fitted with fresh washers. We torque the mounting nuts by hand and finish with a bead of silicone caulk at the base. A level check confirms the spout sits square to the sink.
Test and Cleanup
We pressurize, run hot and cold for two full minutes, and check every joint with a dry paper towel. Any weep shows up immediately. Then we wipe the cabinet, haul the old fixture away, and walk you through the shutoff location before we leave.
13 Years of Fixture Work in Georgetown
Georgetown Bath Remodel Pros has been installing and replacing bathroom faucets across Williamson County since 2013. Our technicians hold a Texas State Board of Plumbing Examiners license and carry EPA Lead-Safe Certification for work in pre-1978 homes, which matters in Old Town and the older blocks near the Square. We have swapped everything from 1980s Delta two-handle sets to modern Kohler and Moen single-hole fixtures with pull-down sprays. We also work to IRC and ADA compliance standards when a fixture needs to meet reach and clearance rules for accessibility.
- 13 years serving Georgetown and Williamson County homeowners since 2013
- Texas State Board of Plumbing Examiners licensed technicians on every job
- EPA Lead-Safe Certified for pre-1978 homes in Old Town and Downtown
- ADA compliance experience for accessible sink and faucet placement
- Hundreds of fixture swaps across Kohler, Moen, Delta, and American Standard lines
Why Georgetown Homeowners Choose Our Faucet Installation
We are a local crew, not a franchise. That means the person who quotes your job is the person who shows up, and the price you hear on the phone is the price on the invoice.
Upfront Flat Pricing
You get a firm number before we start, not an hourly meter. Standard single-fixture swaps run $180 to $450 in 2026, and we tell you which end of that range you are on when we book. No trip charges inside Georgetown.
Same-Week Scheduling
Most faucet jobs get booked within three to five business days, and we hold slots for active leaks. If water is running where it should not be, call 512 325 0295 and we will move you up the list.
Licensed and Insured Crew
Every technician carries a TDLR contractor license and full liability coverage. We pull permits when the scope requires it, which is rare for a like-for-like swap but common when we move supply lines during a bathroom faucet contractor Georgetown TX project.
We Fix the Cause, Not Just the Drip
A leaking faucet repair and replacement Georgetown TX call often ends with a new cartridge, but sometimes the real problem is 60 PSI of pressure hammering old valves. We check pressure, look at the shutoffs, and tell you what will fail next so you can plan for it.
What Our Faucet Installation Includes
Every faucet job we run covers the parts that matter for a leak-free result. We do not nickel-and-dime the small stuff, because a cheap install that fails in six months costs everyone more. Here is what comes standard, and what we quote separately when your job needs it.
What's Included
New Supply Lines
Braided stainless or PEX supply lines go in with every faucet we install. Old rubber and corroded lines are the number one cause of cabinet floods. We size them to the stub-out and torque the fittings to spec.
Shutoff Valve Check
We test both angle stops before we start. If a valve will not close fully or shows corrosion, we replace it for a modest add-on. That single step protects your floors the next time anyone works under the sink.
Drain Assembly Fitting
Pop-up and lift-rod drains get new washers and a fresh seal at the tailpiece. We align the rod so the stopper seats properly and test the drain with a full bowl of water before we finish.
Silicone Seal at Base
A clean bead of silicone caulk at the fixture base keeps splash water out of the countertop hole. We mask the edges, lay a smooth bead, and clean the line so it looks factory-finished.
Pressure and Leak Test
We run hot and cold for two full minutes and check every joint with a dry towel. Any weep shows up before we pack up. You get a walkthrough of the shutoff location before we leave.
Old Fixture Haul-Away
The old faucet, supply lines, and packaging leave with us. No pile of brass and cardboard on your curb. We recycle metal where we can and dispose of the rest properly.
Faucet Problems We Fix in Georgetown
Most faucet calls fall into a handful of categories. Here is what we see most often and how we handle each one.
Faucet drips constantly even when fully closed
Wastes up to 3,000 gallons a year and stains the sink bowl with mineral deposits. The drip gets worse over time as the seat wears further.
We pull the cartridge or stem, inspect the seat, and either rebuild the valve or replace the faucet. If the body is sound, a cartridge swap takes under an hour. If the seat is scored, replacement is the smarter call.
Low water pressure at the bathroom sink only
Points to a clogged aerator or a failing cartridge, not a whole-house issue. Ignoring it usually means the cartridge fails completely within a few months.
We remove and clean the aerator, flush the supply lines, and test flow at the spout. If the cartridge is the bottleneck, we replace it. Most customers see full pressure restored the same visit.
Water pooling inside the vanity cabinet
Cabinet floors swell, particle board fails, and mold can start within 48 hours. This is the most expensive faucet problem we see.
We find the source, which is usually a supply line fitting or a loose packing nut. We replace the lines, dry the cabinet, and check with a moisture meter. If the floor is soft, we quote the repair separately.
Faucet handle is stiff or will not turn
Forces you to grip harder, which eventually cracks the handle or strips the stem. On older fixtures, the whole valve body can fail.
We disassemble the valve, clean mineral scale from the stem, and apply plumber's grease to the moving parts. If the stem is worn, we replace it. On ceramic cartridges, we swap the cartridge.
Water sprays sideways from the spout base
Soaks the countertop and backsplash, and can seep behind the counter into the wall. Usually caused by a failed O-ring or a loose mounting nut.
We pull the faucet, replace the O-rings, and re-seat the fixture with fresh silicone caulk. We check the mounting nuts for torque and confirm the spout sits level before finishing.
When to Call for Faucet Installation
You are updating a 1990s bathroom and the faucet is the last original fixture.
We match the new faucet to your sink hole spread, set it level, and replace the shutoffs while the cabinet is open. If you are also swapping the vanity top, we coordinate so the faucet goes on after the countertop is set.
A finished, modern sink that matches the rest of the room, with new shutoffs that will not seize in five years.
Your shower valve has failed and you have no hot water at the shower.
We open the wall, remove the old valve body, and set a new one at the correct depth for the trim. We waterproof the opening and close it back up with greenboard and paint.
Hot water restored at the shower, with a valve that will last 15 to 20 years and trim that matches your tile.
You are preparing a Sun City Georgetown home for a parent who needs easier grip.
We install lever-handle faucets that meet ADA reach and clearance rules, and set them at a height that works from a seated position. We test handle tension so it moves with light pressure.
A sink that is safe and easy to use, with hardware that meets ADA compliance for accessibility.
A supply line burst under the sink and soaked the cabinet floor.
We shut the water, replace the line and the faucet, dry the cabinet, and check with a moisture meter. If the floor is soft, we quote the repair and coordinate with our flooring crew.
A dry, sound cabinet with new plumbing that will not fail the same way again.
You are selling a Georgetown home and the inspection flagged a dripping faucet.
We repair or replace the fixture, document the work, and leave the sink in working order for the buyer's walkthrough. Most jobs are done in a single visit.
A clean inspection item and a receipt you can hand to the buyer's agent.
Tools and Methods We Use
Tools & Equipment
Pipe Wrench and Basin Wrench
Used to break loose mounting nuts and supply fittings in tight cabinet spaces. The basin wrench reaches behind the sink bowl where a standard wrench will not fit.
Oscillating Multi-Tool
Cuts seized mounting nuts and trimmed caulk lines without damaging the countertop. It also cleans old silicone from the deck edge in seconds.
Caulking Gun
Lays a smooth, even bead of silicone caulk at the fixture base. We use a slow, steady pass and tool the bead with a finger for a clean finish.
Level and Moisture Meter
The level confirms the fixture sits square to the sink. The moisture meter reads the cabinet floor before and after the job to catch hidden leaks.
Hole Saw
Cuts clean faucet holes in quartz and granite countertops when a new spread is needed. We use a diamond-grit bit and keep the cut wet to prevent chipping.
PEX Crimp Tool
Fits new PEX supply lines to the stub-outs when we replace old copper or polybutylene. PEX handles Georgetown's hard water better than the older materials.
Methods
IRC Plumbing Code Compliance
We follow the International Residential Code for supply line sizing, shutoff placement, and drain connections. Georgetown enforces the IRC, so a job that passes our inspection passes the city's. This matters most when we move a supply line or change a drain location.
TCNA Guidelines for Tile Penetrations
When a faucet passes through a tiled backsplash or shower wall, we follow Tile Council of North America guidance for sealing the penetration. That means a proper hole, a clean escutcheon seat, and silicone caulk at the joint.
EPA Lead-Safe Work Practices
Homes built before 1978 may have lead solder at the stub-outs. We follow EPA Lead-Safe Certification procedures when we disturb those joints, which includes containment and proper cleanup. This is standard on Old Town and Downtown Georgetown jobs.
ADA Compliance for Accessible Fixtures
When a customer needs an accessible sink, we set the faucet at the right height and reach for a seated user. Lever handles, reach limits, and clearance all follow ADA compliance rules. We confirm the setup with the customer before we drill.
How Faucet Installation Runs in Georgetown
Georgetown sits on limestone and draws hard water from the Edwards and Trinity aquifers. That mineral content is why we see scale-clogged cartridges and seized handles more often here than in softer-water cities. Homes near the Square and in Old Town often have original 1950s and 1960s plumbing, which means galvanized stub-outs and shutoffs that will not close. We plan for that on every older job. Newer builds in Wolf Ranch and Parkside on the River use PEX and brass shutoffs that hold up better, but the fixtures themselves still wear out in 10 to 15 years. If you are comparing faucet replacement in Georgetown TX cost, the honest answer is that older homes cost more because we often replace the shutoffs and supply lines at the same time. We also watch for freeze damage after a hard winter, since a cracked supply line behind a cabinet wall can drip for weeks before anyone notices.
Service Areas
Many homes here date to the 1950s and 1960s, with galvanized stub-outs and shutoffs that often need replacing. We plan extra time for these jobs.
Active-adult community where lever-handle and ADA-compliant faucets are common requests. We stock models that meet reach and clearance rules.
Newer construction with PEX supply lines and brass shutoffs. Fixture swaps here are usually straightforward, often under three hours.
Mix of 1990s and 2000s builds. Original cartridges are at the end of their life, and we replace them with ceramic options that last longer.
Historic homes near the Square often have lead solder at the stub-outs. We follow EPA Lead-Safe practices on every job here.
Local Considerations
Hard water from Edwards and Trinity aquifers
Mineral scale builds up inside cartridges and aerators, shortening fixture life to 8 to 12 years instead of 15 to 20. We clean and flush supply lines on every install to slow the buildup.
Freeze events in winter
A hard freeze can crack a supply line behind the cabinet wall. We inspect lines for freeze damage on every job from December through February and replace anything that shows stress.
Older homes with galvanized plumbing
Galvanized stub-outs corrode from the inside and restrict flow. When we find them, we replace the visible section with PEX and fit a new shutoff so the next repair is easy.
Limestone bedrock and slab-on-grade construction
Most Georgetown homes are slab-on-grade, so supply lines run through the slab or the walls. We avoid moving lines when we can and work with the existing stub-out locations.
Old Town Two-Handle Swap
A 1962 ranch home near the Square had an original Delta two-handle faucet that dripped constantly. Both shutoff valves were frozen open, and the cabinet floor showed old water staining. The homeowner had been shutting off water at the main for months.
We replaced the faucet, both angle stops, and the supply lines in three hours. The cabinet floor tested dry with a moisture meter. The drip stopped completely, and the homeowner can now shut off water at the sink instead of the main.
Maintenance & Follow-up
Wipe the spout and handles dry weekly to slow scale buildup. Flush the aerator every six months in white vinegar. Check under the cabinet once a season for any sign of moisture.
A Sun City Georgetown homeowner with arthritis could not grip the original round handles. The faucet also sat too far back for comfortable reach from a seated position. Water pressure had dropped to a trickle over two years.
We installed a Moen lever-handle faucet that meets ADA reach and clearance rules. We flushed the supply lines, replaced the shutoffs, and set the fixture forward for easier reach. Pressure returned to full flow, and the homeowner can use the sink without strain.
Maintenance & Follow-up
Apply a drop of plumber's grease to the lever pivot once a year. Keep the area under the sink clear so the shutoffs stay accessible. Test the lever tension every few months.
A 2004 Berry Creek home lost hot water at the shower. The valve body had failed internally, and the trim was corroded. The wall behind the tile showed early signs of moisture damage from a slow leak at the valve seat.
We opened the wall, replaced the valve body, and installed new trim. We waterproofed the opening with cement backer board and membrane, then closed it with greenboard and paint. Hot water returned, and the wall tested dry after a full week.
Maintenance & Follow-up
Run the shower for a minute after each use to clear standing water from the valve. Check the trim screws twice a year for looseness. Watch for any discoloration on the wall near the valve.
How much does bathroom faucet installation cost in Georgetown TX?
Most single-fixture installs run $180 to $450 in 2026, including labor, new supply lines, and a fresh shutoff valve. Cost climbs when the countertop needs repair, when the old fixture is seized, or when you choose a high-end widespread set. Shower valve swaps run higher because the wall has to be opened and closed. We give you a firm number before we start.
How long does faucet replacement take in Georgetown Texas?
A standard sink faucet takes two to four hours from shutoff to cleanup. That includes removing the old fixture, prepping the deck, fitting new supply lines, and testing. If we find a corroded shutoff or a cracked countertop edge, add an hour. Shower faucet installation Georgetown jobs usually take a full day because of the wall work.
How to fix a leaking bathroom faucet in Georgetown TX?
First, shut the water off at the angle stops under the sink. If the drip comes from the spout, the cartridge or seat is worn and needs replacing. If it leaks at the base, the O-ring or mounting nut is the culprit. If it drips from the handle, it is usually a worn stem. We diagnose it in about 15 minutes and quote the fix before touching anything.
Do I need a permit for faucet installation in Georgetown TX?
A straight like-for-like swap does not require a permit in Georgetown. You do need one when the work involves moving supply lines, changing the drain location, or altering the venting, which falls under the IRC plumbing code the city enforces. We handle the paperwork when a permit is required and tell you upfront if your job crosses that line.
Licensed, Insured, and Local
Certifications
Reviews
Fast, clean, and honest. They replaced our kitchen and bathroom faucets in one visit and showed me the old shutoff that was about to fail. Price matched the quote. I have already recommended them to a neighbor in Berry Creek.
Called about a leaking faucet and they got us in the same week. The technician explained what was wrong, replaced the cartridge, and did not try to upsell a whole new fixture. Fair price and no mess left behind.
We used them for a shower valve replacement in our Sun City home. They opened the wall, replaced the valve, and had it painted and back together in a day. The tile work around the trim looked original. Very professional crew.
Old Town home with 1960s plumbing. They replaced both shutoffs and the faucet, and followed lead-safe practices without being asked. Explained everything before starting. This is the kind of local crew you want on an older house.
Related Services
Full Bathroom Remodeling
When a faucet swap turns into a full refresh, we handle tile, vanity, lighting, and fixtures as one project. Most Georgetown full remodels run three to five weeks and include new supply lines and shutoffs at every fixture.
Full Bathroom RemodelingBathroom Renovation
A renovation updates the room without moving walls. New faucets pair naturally with fresh paint, a quartz countertop, and updated lighting. We sequence the trades so your sink is out of service for days, not weeks.
Bathroom RenovationShower Remodeling
Shower remodels almost always involve a new valve and trim, which is shower faucet installation Georgetown work at its core. We open the wall, set the valve body at the right depth, and waterproof before tile goes back.
Shower RemodelingBathtub Remodeling
Tub decks often carry a roman or deck-mount faucet that needs replacing when the tub does. We set the new fixture on the deck, seal it properly, and check the drain alignment before the surround goes up.
Bathtub RemodelingWalk-In Tub Installation
Walk-in tubs come with their own filler and hand-shower hardware. We tie those into your existing supply, add shutoffs inside the access panel, and test every joint before the panel is closed.
Walk-In Tub InstallationTile Installation
Faucet work and tile work overlap at every backsplash and shower wall. We cut tile around the stub-outs with a wet saw and hole saw so the escutcheon sits flat, then seal the penetration with silicone caulk.
Tile InstallationVanity Installation
A new vanity means new faucet holes, a new drain location, and often a different spread. We set the cabinet, drill the deck, and fit the faucet so the spout centers over the bowl.
Vanity InstallationBathroom Flooring Installation
Water damage from a failed supply line often reaches the floor. We replace the subfloor, lay new porcelain tile or LVT, and reinstall the fixtures once the moisture meter reads dry.
Bathroom Flooring InstallationBathroom Countertop Installation
New quartz or granite countertops get drilled for the faucet on site. We measure the spread, cut clean holes with a hole saw, and set the fixture with fresh silicone caulk at the base.
Bathroom Countertop InstallationToilet Installation
Toilets and faucets share the same supply system and the same shutoff valves. When we are already under the cabinet, we check the toilet supply line and replace it if it shows corrosion or stiffening.
Toilet InstallationSink Installation
Undermount and drop-in sinks both need the faucet set after the bowl is secured. We install the sink, seal the rim, then fit the faucet and drain as one assembly so nothing has to come apart twice.
Sink InstallationShower Door Installation
New shower doors change how water hits the valve and trim. We check for leaks at the valve after the door goes on, since splash patterns can reveal a seal that was fine before.
Shower Door InstallationBathtub-to-Shower Conversion
Conversions require a new shower valve, trim, and often a hand-shower on a slide bar. We rough in the valve, waterproof the walls, and set the trim after tile so the escutcheon sits flush.
Bathtub-to-Shower ConversionAccessible Bathroom Remodeling
ADA-compliant faucets use lever handles and reach limits that matter for wheelchair users. We set the fixture at the right height and clearance, and confirm the reach range meets ADA compliance.
Accessible Bathroom RemodelingBathroom Cabinets and Storage
Cabinet depth affects how easily you can reach the shutoffs. We plan storage around the plumbing wall so you keep access to the valves without emptying a drawer every time.
Bathroom Cabinets and StorageBathroom Ventilation and Exhaust Fan Installation
Steam and humidity shorten faucet cartridge life. A properly sized exhaust fan moving 50 to 110 CFM keeps the room drier and slows corrosion on chrome and brass trim.
Bathroom Ventilation and Exhaust Fan InstallationBathroom Waterproofing
Waterproofing membrane behind the shower wall protects the framing from valve leaks. We install cement backer board and membrane before the trim goes on, so a slow drip never reaches the studs.
Bathroom WaterproofingBathroom Drywall and Painting
Shower valve swaps require opening the wall. We patch with greenboard, tape, texture, and paint so the repair disappears once the escutcheon and trim are back in place.
Bathroom Drywall and PaintingWhat Georgetown Customers Say
Real experiences from customers who chose our Faucet Installation services
"Our 1950s sink had a Delta two-handle set that dripped constantly. They replaced the faucet and both shutoff valves in about three hours. The technician showed me where the old valve was weeping onto the cabinet floor and fixed that too. Price matched the quote exactly. No mess left behind."
Marcus T.
Homeowner, Old Town Georgetown
"I needed a lever-handle faucet because of arthritis in my hands. They recommended a Moen model that met ADA reach requirements and installed it the same week. The technician adjusted the handle tension so it moves easily. I can use the sink again without struggling. Very patient with my questions."
Diane R.
Homeowner, Sun City Georgetown
"Shower valve failed and we had no hot water at the shower. They opened the wall, set a new valve body, waterproofed, and had it back together in a day. Tile matched perfectly. They also replaced the sink faucet while they were here since it was on the same list. Fair price for two fixtures."
Kevin S.
Homeowner, Berry Creek
Book Bathroom Faucet Installation Georgetown TX Today
Dripping faucets waste water and get worse. We give you a firm price, show up when we say, and leave the cabinet cleaner than we found it. Call 512 325 0295 and we will get you on the schedule this week.